Page 1 of 1

8200N BT FTTC Connection Instructions

Posted: Sat Sep 21, 2013 12:39 pm
by Brian Coat
I'm struggling to get a connection using the little UK set up guide booklet that came with my 8200n

Please can anyone point me to some clear instructions for how to get this modem/router to hook up to BT FTTC?

One with screenshots would really help?

Thanks.

BC

Re: 8200N BT FTTC Connection Instructions

Posted: Sat Sep 21, 2013 8:14 pm
by Brian Coat
OK so now I'm registered to the forum, I found I could download a more legible version of the booklet from this board. Great!

So I tried again and still got no joy.

Here are settings and logs.

SETTINGS (I have screen shots but can't figure how to easily cut n paste them.)

VLAN Group Parameters: BT, 101, five ticks [four ports and WLAN], Tag WAN (NAT)
Username: bthomehub@btbroadband.com Password: BT
IP Address: 0.0.0.0
Authentication Protocol : Auto

Main Port: VDSL
Protocol: PPoE

ALL THE SCREENS LOOK EXACTLY LIKE THE GUIDE except VLAN Group Parameters where the screen in the guide has no WLAN box column to tick.

Software:1.06a.dt6

STATUS
Ethernet, VDSL, Wireless all have green ticks EWAN has red cross
Connection: Connecting ... then .... No Response


SYSTEM LOG

Jan 1 00:00:16 syslog: VDSL init port Fail!!! Will be retry.Jan 1 00:00:25 syslog: pppoe main==>startJan 1 00:00:25 PPPoE: PPPoE: Use brwan for PPPoE discovery Jan 1 00:00:25 PPPoE: pppoe module startedJan 1 00:00:27 dnsmasq[317]: using nameserver 8.8.4.4#53Jan 1 00:00:27 dnsmasq[317]: using nameserver 8.8.8.8#53Jan 1 00:00:27 UPNPD[328]: HTTP listening on port 2800Jan 1 00:00:27 UPNPD[328]: uuidvalue=uuid:28802880-2880-1880-a880-0004edc40694Jan 1 00:00:42 syslog: webs: admin (192.168.1.100) login...Jan 1 00:01:15 PPPoE: Connection failedJan 1 00:01:15 PPPoE: Doing disconnectJan 1 00:02:35 PPPoE: Connection failedJan 1 00:02:35 PPPoE: Doing disconnectJan 1 00:03:55 PPPoE: Connection failedJan 1 00:03:55 PPPoE: Doing disconnect


Line tested as OK using BT Open Reach Box and HH3



**** ANYONE GOT ANY IDEAS **** ?????????

Thanks.

BC

Re: 8200N BT FTTC Connection Instructions

Posted: Tue Sep 24, 2013 12:34 pm
by billion_fan
Brian Coat wrote:OK so now I'm registered to the forum, I found I could download a more legible version of the booklet from this board. Great!

So I tried again and still got no joy.

Here are settings and logs.

SETTINGS (I have screen shots but can't figure how to easily cut n paste them.)

VLAN Group Parameters: BT, 101, five ticks [four ports and WLAN], Tag WAN (NAT)
Username: bthomehub@btbroadband.com Password: BT
IP Address: 0.0.0.0
Authentication Protocol : Auto

Main Port: VDSL
Protocol: PPoE

ALL THE SCREENS LOOK EXACTLY LIKE THE GUIDE except VLAN Group Parameters where the screen in the guide has no WLAN box column to tick.

Software:1.06a.dt6

STATUS
Ethernet, VDSL, Wireless all have green ticks EWAN has red cross
Connection: Connecting ... then .... No Response


SYSTEM LOG

Jan 1 00:00:16 syslog: VDSL init port Fail!!! Will be retry.Jan 1 00:00:25 syslog: pppoe main==>startJan 1 00:00:25 PPPoE: PPPoE: Use brwan for PPPoE discovery Jan 1 00:00:25 PPPoE: pppoe module startedJan 1 00:00:27 dnsmasq[317]: using nameserver 8.8.4.4#53Jan 1 00:00:27 dnsmasq[317]: using nameserver 8.8.8.8#53Jan 1 00:00:27 UPNPD[328]: HTTP listening on port 2800Jan 1 00:00:27 UPNPD[328]: uuidvalue=uuid:28802880-2880-1880-a880-0004edc40694Jan 1 00:00:42 syslog: webs: admin (192.168.1.100) login...Jan 1 00:01:15 PPPoE: Connection failedJan 1 00:01:15 PPPoE: Doing disconnectJan 1 00:02:35 PPPoE: Connection failedJan 1 00:02:35 PPPoE: Doing disconnectJan 1 00:03:55 PPPoE: Connection failedJan 1 00:03:55 PPPoE: Doing disconnect


Line tested as OK using BT Open Reach Box and HH3



**** ANYONE GOT ANY IDEAS **** ?????????

Thanks.

BC
Try the attached firmware, don't forget to reset back to factory default settings and manually reconfigure the device again.

Re: 8200N BT FTTC Connection Instructions

Posted: Fri Oct 25, 2013 7:00 pm
by skydemon
billion_fan wrote:
Brian Coat wrote:OK so now I'm registered to the forum, I found I could download a more legible version of the booklet from this board. Great!

So I tried again and still got no joy.

Here are settings and logs.

SETTINGS (I have screen shots but can't figure how to easily cut n paste them.)

VLAN Group Parameters: BT, 101, five ticks [four ports and WLAN], Tag WAN (NAT)
Username: bthomehub@btbroadband.com Password: BT
IP Address: 0.0.0.0
Authentication Protocol : Auto

Main Port: VDSL
Protocol: PPoE

ALL THE SCREENS LOOK EXACTLY LIKE THE GUIDE except VLAN Group Parameters where the screen in the guide has no WLAN box column to tick.

Software:1.06a.dt6

STATUS
Ethernet, VDSL, Wireless all have green ticks EWAN has red cross
Connection: Connecting ... then .... No Response


SYSTEM LOG

Jan 1 00:00:16 syslog: VDSL init port Fail!!! Will be retry.Jan 1 00:00:25 syslog: pppoe main==>startJan 1 00:00:25 PPPoE: PPPoE: Use brwan for PPPoE discovery Jan 1 00:00:25 PPPoE: pppoe module startedJan 1 00:00:27 dnsmasq[317]: using nameserver 8.8.4.4#53Jan 1 00:00:27 dnsmasq[317]: using nameserver 8.8.8.8#53Jan 1 00:00:27 UPNPD[328]: HTTP listening on port 2800Jan 1 00:00:27 UPNPD[328]: uuidvalue=uuid:28802880-2880-1880-a880-0004edc40694Jan 1 00:00:42 syslog: webs: admin (192.168.1.100) login...Jan 1 00:01:15 PPPoE: Connection failedJan 1 00:01:15 PPPoE: Doing disconnectJan 1 00:02:35 PPPoE: Connection failedJan 1 00:02:35 PPPoE: Doing disconnectJan 1 00:03:55 PPPoE: Connection failedJan 1 00:03:55 PPPoE: Doing disconnect


Line tested as OK using BT Open Reach Box and HH3



**** ANYONE GOT ANY IDEAS **** ?????????

Thanks.

BC
Try the attached firmware, don't forget to reset back to factory default settings and manually reconfigure the device again.
Where did you get that firmware all i could find was BiPAC 8200N 1.06a.dt6 firmware ..........Thanks

Re: 8200N BT FTTC Connection Instructions

Posted: Mon Feb 02, 2015 10:32 pm
by Wizwiz
Hi
Try this worked for me perfectly
Log into router 8200n
User_ admin
Pass- admin (default)
1 - click on ADVANCED. in left window
2- click on CONFIGURATION
3- then click on ADVANCED in the droppdown menu
4- click on VLAN
5- in the parameters windows use these settings
VLAN group name =BT
VLAN id = 101
Ethernet ports and wlan ports TICK ALL BOXES
wan tag = tag wan(nat)

Click APPLY
CLICK SAVE CONFIG

that's it your connected.

Re: 8200N BT FTTC Connection Instructions

Posted: Wed Apr 08, 2015 12:20 pm
by metalliblob
Thanks for this info.
I was having same problem.
My BT Hub 5 was resetting every night due to a so called software update call from BT's side so lets see what happens now. This was crippling my connection :( .
Got a 8200N to see if its better, although my upload is less hopefully it will get a chance to retrain up.
THANKS AGAIN!!
:D