WAN protocol

Post Reply
norsenoddy
Posts: 22
Joined: Fri Jun 03, 2016 12:09 pm

WAN protocol

Post by norsenoddy »

Hi would it be possible to confirm the wan protocol settings for 7800n ? isp plusnet not sure it's quite right after full reset cheers
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: WAN protocol

Post by billion_fan »

norsenoddy wrote:Hi would it be possible to confirm the wan protocol settings for 7800n ? isp plusnet not sure it's quite right after full reset cheers
PPPOA for ADSL
PPPOE for EWAN when connecting to a fibre modem
norsenoddy
Posts: 22
Joined: Fri Jun 03, 2016 12:09 pm

Re: WAN protocol

Post by norsenoddy »

Thanks for that it was right but worth double checking :)
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: WAN protocol

Post by billion_fan »

pugs66 wrote:
billion_fan wrote:
norsenoddy wrote:Hi would it be possible to confirm the wan protocol settings for 7800n ? isp plusnet not sure it's quite right after full reset cheers
PPPOA for ADSL
PPPOE for EWAN when connecting to a fibre modem
Billion_Fan, can you confirm for connecting to a vsdl modem that ethernet should be set to PPPOE or IPoE please, confusion over on the 7800DXL board on what is the proper settings for BT HH5

On the 7800N the setup methods is as follows

Sky ADSL - PPPOA
BT/PlusNet ADSL - PPPOA
Talktalk ADSL - PPPOA
BT/PlusNet Fibre - EWAN >>> PPPOE
Sky Fibre - EWAN >> Obtain a IP address automatically >> Client ID (in the client ID section enter your username and password that is extracted from your current Sky Fibre modem/router with a '|' inbetween eg username@skydsl|password
Talktalk Fibre - EWAN >> Obtain a IP address automatically
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: WAN protocol

Post by billion_fan »

pugs66 wrote:
billion_fan wrote:
norsenoddy wrote:Hi would it be possible to confirm the wan protocol settings for 7800n ? isp plusnet not sure it's quite right after full reset cheers
PPPOA for ADSL
PPPOE for EWAN when connecting to a fibre modem
Billion_Fan, can you confirm for connecting to a vsdl modem that ethernet should be set to PPPOE or IPoE please, confusion over on the 7800DXL board on what is the proper settings for BT HH5
When using the HH5, as the device can't be configured in modem only mode, the only option is to use IPOE (7800DXL)

1. Make sure you change the IP address of the 7800DXL so it does not match the same subnet as the HH5, eg HH5 - 192.168.1.x, 7800DXL - 192.168.2.x, once the 7800DXL obtains a internal IP address from the HH5, DMZ this IP address within the HH5
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: WAN protocol

Post by billion_fan »

pugs66 wrote:Thanks Billion. Question I have done this and all works ok but what should the Firewall settings be, enabled on both the router and HH5 or just the router? I take it all ports should be forwarded to the 7800 and UPN also disabled on the HH5? Basiclly is their any secuirty issues?
I would leave the firewall on, on both devices, as both devices will have access to the internet
Post Reply