8800nl errors (Plusnet)

Discussions for BiPAC 8800 series: 8800NL, 8800NLR2, 8800AXL, 8800AXLR2
Post Reply
muttyhc
Posts: 6
Joined: Fri Mar 13, 2015 8:46 pm

8800nl errors (Plusnet)

Post by muttyhc »

Hi all,

I have had the 8800nl for about a month now, it was very stable on my talktalk line but I recently changed to Plusnet and it has been fine, but the quantity of errors seems to have dramatically increased.

This morning my internet had essentially stopped working and I had to reboot the 8800nl.

I decided to update the firmware to d39 since then,

Now it has been synced for the past 30 minutes since updating and it has the following error readout.

HEC Errors 114 0
OCD Errors 0 0
LCD Errors 0 0
Total Cells 134285110 0
Data Cells 1695407 0
Bit Errors 0 0
Total ES 58 2
Total SES 0 0
Total UAS 28 28

My downstream is 42578 upstream is 12504

This has dropped from 48mbps since the line went live.

I read through the entire 8800nl thread and noticed this chipset does produce more errors, so was considering going for the openreach modem in bridge mode with a router connected - do I have any reason to pursue this?

Further info:

Line Coding (Trellis) On On
SNR Margin (dB) 6.1 6.1
Attenuation (dB) 20.1 0.0
Output Power (dBm) 13.3 6.9
Attainable Rate (Kbps) 49906 12692


Any help appreciated.
Thanks
Top
witty245
Posts: 2
Joined: Tue Apr 21, 2015 8:50 am

Re: 8800nl errors (Plusnet)

Post by witty245 »

hello just looking at your post i have the 8800 axl i got a lot of dsl drops that were associated with using impulse noise reduction also referd to as PhyR this is enabled by default plus net does not support this function i now this because plus net told me and my adsl connection is now supper stable
Top
Billion-Pad
Posts: 10
Joined: Sat Apr 11, 2015 8:01 am

Re: 8800nl errors (Plusnet)

Post by Billion-Pad »

Hi just come across this thread and was interested in the last post regards to Phyr impulse noise reduction I'm on bt infinity2 with billion 8800axl been using it for 2 months now to replace hh5a much more reliable but have been getting a lot of errors on downstream but hardly anything on upstream so checked my configuration/wan settings/DSL and noticed that
PhyR Is enabled for downstream but not up so I disabled it and noticed that the errors on downstream have more than halved, I'm not quite sure but is this setting something to do with g.inp I'm on a eci cabinet and as yet none have been g.inp enabled yet due to various compatibility problems ?

Current stats

Status
xDSL
xDSL
Mode VDSL2
Traffic Type PTM
Status Up
Link Power State L0
Downstream Upstream
Line Coding (Trellis) On On
SNR Margin (dB) 6.4 6.4
Attenuation (dB) 17.3 0.0
Output Power (dBm) 13.5 5.9
Attainable Rate (Kbps) 64692 22612
Rate (Kbps) 63427 20000
B (# of bytes in Mux Data Frame) 239 236
M (# of Mux Data Frames in an RS codeword) 1 1
T (# of Mux Data Frames in an OH sub-frame) 21 5
R (# of redundancy bytes in the RS codeword) 0 16
S (# of data symbols over which the RS code word spans) 0.1204 0.3771
L (# of bits transmitted in each data symbol) 15944 5410
D (interleaver depth) 1 1
I (interleaver block size in bytes) 240 255
N (RS codeword size) 240 255
Delay (msec) 0 0
INP (DMT symbol) 0.00 0.00
OH Frames 0 0
OH Frame Errors 14 0
RS Words 0 2835582
RS Correctable Errors 0 2
RS Uncorrectable Errors 0 0
HEC Errors 84 0
OCD Errors 0 0
LCD Errors 0 0
Total Cells 230167518 0
Data Cells 64570 0
Bit Errors 0 0
Total ES 9 0
Total SES 0 0
Total UAS 0 0
Top
muttyhc
Posts: 6
Joined: Fri Mar 13, 2015 8:46 pm

Re: 8800nl errors (Plusnet)

Post by muttyhc »

I have disabled PhysR after returning to my 8800NL - was not using it for some time.

I will monitor errors with PhysR off.

Is there a consensus on the best firmware for this??
Top
muttyhc
Posts: 6
Joined: Fri Mar 13, 2015 8:46 pm

Re: 8800nl errors (Plusnet)

Post by muttyhc »

Hi, getting disconnects in the middle of the night - wondering if anyone had any ideas why? Here is my log.

Jul 23 03:45:39 daemon crit kernel: Line 0: VDSL2 link down
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = PTM
Jul 23 03:45:39 daemon warn kernel: HOST XTM tx ch 0 disabled.
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
Jul 23 03:45:39 daemon warn kernel: TxLineRateTimer=0
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 0
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jul 23 03:45:42 daemon notice syslog: pppd:Terminating on signal 20.
Jul 23 03:45:42 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
Jul 23 03:45:42 daemon crit syslog: Clear IP addresses. Connection DOWN.
Jul 23 03:45:42 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 23 03:45:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:45:47 daemon info kernel: device ptm0 left promiscuous mode
Jul 23 03:45:47 daemon info kernel: device ptm0 entered promiscuous mode
Jul 23 03:45:47 daemon info kernel: device ptm0 left promiscuous mode
Jul 23 03:45:49 daemon crit kernel: Line 0: VDSL G.993 started
Jul 23 03:46:07 daemon crit kernel: Line 0: VDSL2 link up, Bearer 0, us=12280, ds=34999
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = PTM
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jul 23 03:46:07 daemon warn kernel: TxLineRateTimer=2606
Jul 23 03:46:07 daemon warn kernel: bcmxtmrt: MAC address: 60 03 47 0d 63 0f
Jul 23 03:46:07 daemon warn kernel: [DoCreateDeviceReq.3087]: register_netdev
Jul 23 03:46:07 daemon warn kernel: [DoCreateDeviceReq.3089]: register_netdev done
Jul 23 03:46:07 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 0
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve PTM vcid=0 ptmPri=1 port=0 bondingPort=4
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve PTM vcid=1 ptmPri=2 port=0 bondingPort=4
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve MP group=0 priority=0 weight=1
Jul 23 03:46:07 daemon warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa47c8000
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=12280000, DS=34999000
Jul 23 03:46:07 daemon warn kernel: [FAP1] xtmCreateDevice : devId 0, encapType 0, headerLen 0
Jul 23 03:46:07 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
Jul 23 03:46:07 daemon warn kernel: [FAP1] xtmLinkUp : devId 0, matchId 0
Jul 23 03:46:07 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 1
Jul 23 03:46:07 daemon warn kernel: [FAP1] xtmLinkUp : devId 0, matchId 1
Jul 23 03:46:07 daemon warn kernel: ptm0.1 MAC address set to 60:03:47:0D:63:10
Jul 23 03:46:07 daemon warn kernel: netdev path : ptm0.1
Jul 23 03:46:07 daemon info kernel: -> ptm0
Jul 23 03:46:07 daemon warn kernel: BCMVLAN : ptm0 mode was set to RG
Jul 23 03:46:07 daemon info kernel: device ptm0 entered promiscuous mode
Jul 23 03:46:07 daemon notice syslog: pppd:cms logging initialized.
Jul 23 03:46:07 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jul 23 03:46:07 daemon notice syslog: PPP: Start to connect ...
Jul 23 03:46:34 daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected
Jul 23 03:46:34 daemon notice syslog: pppd:Couldn't reset tty to normal line discipline: Inappropriate ioctl for device
Jul 23 03:46:34 daemon notice syslog: pppd:Doing disconnect
Jul 23 03:46:37 daemon notice syslog: PPP: Start to connect ...
Jul 23 03:46:42 daemon crit syslog: PPP server detected.
Jul 23 03:46:42 daemon crit syslog: PPP session established.
Jul 23 03:46:42 daemon warn kernel: netdev path : ppp0.1 -> ptm0.1 -> ptm0
Jul 23 03:46:42 daemon notice syslog: pppd:Using interface ppp0.1
Jul 23 03:46:42 daemon notice syslog: pppd:Connect: ppp0.1 <--> ptm0.1
Jul 23 03:46:42 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon crit syslog: PPP LCP UP.
Jul 23 03:46:42 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon crit syslog: PPP LCP UP.
Jul 23 03:46:43 daemon notice syslog: pppd:local IP address 87.112.30.221
Jul 23 03:46:43 daemon notice syslog: pppd:remote IP address 195.166.128.183
Jul 23 03:46:43 daemon notice syslog: pppd:primary DNS address 212.159.6.9
Jul 23 03:46:43 daemon notice syslog: pppd:secondary DNS address 212.159.6.10
Jul 23 03:46:43 daemon crit syslog: Received valid IP address from server. Connection UP.
Jul 23 03:46:45 daemon warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache flushing the flows^[[0m
Top
billion_fan
Posts: 5398
Joined: Tue Jul 19, 2011 4:30 pm

Re: 8800nl errors (Plusnet)

Post by billion_fan »

muttyhc wrote:Hi, getting disconnects in the middle of the night - wondering if anyone had any ideas why? Here is my log.

Jul 23 03:45:39 daemon crit kernel: Line 0: VDSL2 link down
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = PTM
Jul 23 03:45:39 daemon warn kernel: HOST XTM tx ch 0 disabled.
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
Jul 23 03:45:39 daemon warn kernel: TxLineRateTimer=0
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 0
Jul 23 03:45:39 daemon warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jul 23 03:45:42 daemon notice syslog: pppd:Terminating on signal 20.
Jul 23 03:45:42 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
Jul 23 03:45:42 daemon crit syslog: Clear IP addresses. Connection DOWN.
Jul 23 03:45:42 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 23 03:45:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:45:47 daemon info kernel: device ptm0 left promiscuous mode
Jul 23 03:45:47 daemon info kernel: device ptm0 entered promiscuous mode
Jul 23 03:45:47 daemon info kernel: device ptm0 left promiscuous mode
Jul 23 03:45:49 daemon crit kernel: Line 0: VDSL G.993 started
Jul 23 03:46:07 daemon crit kernel: Line 0: VDSL2 link up, Bearer 0, us=12280, ds=34999
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = PTM
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jul 23 03:46:07 daemon warn kernel: TxLineRateTimer=2606
Jul 23 03:46:07 daemon warn kernel: bcmxtmrt: MAC address: 60 03 47 0d 63 0f
Jul 23 03:46:07 daemon warn kernel: [DoCreateDeviceReq.3087]: register_netdev
Jul 23 03:46:07 daemon warn kernel: [DoCreateDeviceReq.3089]: register_netdev done
Jul 23 03:46:07 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 0
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve PTM vcid=0 ptmPri=1 port=0 bondingPort=4
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve PTM vcid=1 ptmPri=2 port=0 bondingPort=4
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Reserve MP group=0 priority=0 weight=1
Jul 23 03:46:07 daemon warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa47c8000
Jul 23 03:46:07 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=12280000, DS=34999000
Jul 23 03:46:07 daemon warn kernel: [FAP1] xtmCreateDevice : devId 0, encapType 0, headerLen 0
Jul 23 03:46:07 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
Jul 23 03:46:07 daemon warn kernel: [FAP1] xtmLinkUp : devId 0, matchId 0
Jul 23 03:46:07 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 1
Jul 23 03:46:07 daemon warn kernel: [FAP1] xtmLinkUp : devId 0, matchId 1
Jul 23 03:46:07 daemon warn kernel: ptm0.1 MAC address set to 60:03:47:0D:63:10
Jul 23 03:46:07 daemon warn kernel: netdev path : ptm0.1
Jul 23 03:46:07 daemon info kernel: -> ptm0
Jul 23 03:46:07 daemon warn kernel: BCMVLAN : ptm0 mode was set to RG
Jul 23 03:46:07 daemon info kernel: device ptm0 entered promiscuous mode
Jul 23 03:46:07 daemon notice syslog: pppd:cms logging initialized.
Jul 23 03:46:07 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jul 23 03:46:07 daemon notice syslog: PPP: Start to connect ...
Jul 23 03:46:34 daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected
Jul 23 03:46:34 daemon notice syslog: pppd:Couldn't reset tty to normal line discipline: Inappropriate ioctl for device
Jul 23 03:46:34 daemon notice syslog: pppd:Doing disconnect
Jul 23 03:46:37 daemon notice syslog: PPP: Start to connect ...
Jul 23 03:46:42 daemon crit syslog: PPP server detected.
Jul 23 03:46:42 daemon crit syslog: PPP session established.
Jul 23 03:46:42 daemon warn kernel: netdev path : ppp0.1 -> ptm0.1 -> ptm0
Jul 23 03:46:42 daemon notice syslog: pppd:Using interface ppp0.1
Jul 23 03:46:42 daemon notice syslog: pppd:Connect: ppp0.1 <--> ptm0.1
Jul 23 03:46:42 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon crit syslog: PPP LCP UP.
Jul 23 03:46:42 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 23 03:46:42 daemon crit syslog: PPP LCP UP.
Jul 23 03:46:43 daemon notice syslog: pppd:local IP address 87.112.30.221
Jul 23 03:46:43 daemon notice syslog: pppd:remote IP address 195.166.128.183
Jul 23 03:46:43 daemon notice syslog: pppd:primary DNS address 212.159.6.9
Jul 23 03:46:43 daemon notice syslog: pppd:secondary DNS address 212.159.6.10
Jul 23 03:46:43 daemon crit syslog: Received valid IP address from server. Connection UP.
Jul 23 03:46:45 daemon warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache flushing the flows^[[0m
Ask the ISP to investigate, as the we can see daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected which means no response from the isp/dslam, also ask them to do a full line check in case there are any other issues
Top
muttyhc
Posts: 6
Joined: Fri Mar 13, 2015 8:46 pm

Re: 8800nl errors (Plusnet)

Post by muttyhc »

Will give them a call in the morning to go through this.

Having more issues tonight.

We were streaming from amazon instant video this evening and basically the streaming came to a complete halt, and the hec errors were multiplying by the thousands every second. My log was displaying these messages...

Jul 23 21:14:30 daemon err syslog: dhcpd:sending OFFER of 192.168.1.100
Jul 23 21:14:30 daemon err syslog: dhcpd:sending ACK to 192.168.1.100
Jul 23 21:14:38 daemon err syslog: dhcpd:sending OFFER of 192.168.1.101
Jul 23 21:14:38 daemon err syslog: dhcpd:sending ACK to 192.168.1.101

I have changed around cables and homeplugs and it has happened before already. Seems to happen around this time of day.

Any insight?
Top
billion_fan
Posts: 5398
Joined: Tue Jul 19, 2011 4:30 pm

Re: 8800nl errors (Plusnet)

Post by billion_fan »

muttyhc wrote:Will give them a call in the morning to go through this.

Having more issues tonight.

We were streaming from amazon instant video this evening and basically the streaming came to a complete halt, and the hec errors were multiplying by the thousands every second. My log was displaying these messages...

Jul 23 21:14:30 daemon err syslog: dhcpd:sending OFFER of 192.168.1.100
Jul 23 21:14:30 daemon err syslog: dhcpd:sending ACK to 192.168.1.100
Jul 23 21:14:38 daemon err syslog: dhcpd:sending OFFER of 192.168.1.101
Jul 23 21:14:38 daemon err syslog: dhcpd:sending ACK to 192.168.1.101

I have changed around cables and homeplugs and it has happened before already. Seems to happen around this time of day.

Any insight?
The logs are just DHCP logs, so I don't think that is related, if the issue occurs the same time every day, and you get lots of HEC errors, then it looks like a line issue
Top
muttyhc
Posts: 6
Joined: Fri Mar 13, 2015 8:46 pm

Re: 8800nl errors (Plusnet)

Post by muttyhc »

Thanks for the input,

Well I went back to dm2 firmware the night before last and my line was up for a good 26/27 hours and then last night resynced at a lower speed (dropped from 40mbps to 32mbps in the past week)

Errors were very low as well on the dm2 firmware, however after the resync in the middle of the night it is erroring more.

After 5-6 hours it is now looking like this,

HEC Errors 791 0
OCD Errors 0 0
LCD Errors 0 0
Total Cells 1451382136 0
Data Cells 48704264 0
Bit Errors 0 0
Total ES 130 50
Total SES 10 1
Total UAS 54 54

Log last night was:

ul 25 04:01:09 daemon crit kernel: Line 0: VDSL2 link down
Jul 25 04:01:09 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = PTM
Jul 25 04:01:09 daemon warn kernel: HOST XTM tx ch 0 disabled.
Jul 25 04:01:09 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
Jul 25 04:01:09 daemon warn kernel: TxLineRateTimer=0
Jul 25 04:01:09 daemon warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 0
Jul 25 04:01:09 daemon warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jul 25 04:01:11 daemon crit kernel: Line 0: xDSL G.994 training
Jul 25 04:01:12 daemon notice syslog: pppd:Terminating on signal 20.
Jul 25 04:01:12 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
Jul 25 04:01:12 daemon crit syslog: Clear IP addresses. Connection DOWN.
Jul 25 04:01:12 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:01:12 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:01:17 daemon info kernel: device ptm0 left promiscuous mode
Jul 25 04:01:17 daemon info kernel: device ptm0 entered promiscuous mode
Jul 25 04:01:17 daemon info kernel: device ptm0 left promiscuous mode
Jul 25 04:01:19 daemon crit kernel: Line 0: VDSL G.993 started
Jul 25 04:01:36 daemon crit kernel: Line 0: VDSL2 link up, Bearer 0, us=10767, ds=32400
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = PTM
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jul 25 04:01:36 daemon warn kernel: TxLineRateTimer=2972
Jul 25 04:01:36 daemon warn kernel: bcmxtmrt: MAC address: 60 03 47 0d 63 0f
Jul 25 04:01:36 daemon warn kernel: [DoCreateDeviceReq.3087]: register_netdev
Jul 25 04:01:36 daemon warn kernel: [DoCreateDeviceReq.3089]: register_netdev done
Jul 25 04:01:36 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 0
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: Reserve PTM vcid=0 ptmPri=1 port=0 bondingPort=4
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: Reserve PTM vcid=1 ptmPri=2 port=0 bondingPort=4
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: Reserve MP group=0 priority=0 weight=1
Jul 25 04:01:36 daemon warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa3000000
Jul 25 04:01:36 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=10767000, DS=32400000
Jul 25 04:01:36 daemon warn kernel: [FAP1] xtmCreateDevice : devId 0, encapType 0, headerLen 0
Jul 25 04:01:36 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
Jul 25 04:01:36 daemon warn kernel: [FAP1] xtmLinkUp : devId 0, matchId 0
Jul 25 04:01:36 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 1
Jul 25 04:01:36 daemon warn kernel: [FAP1] xtmLinkUp : devId 0, matchId 1
Jul 25 04:01:36 daemon warn kernel: ptm0.1 MAC address set to 60:03:47:0D:63:10
Jul 25 04:01:36 daemon warn kernel: netdev path : ptm0.1 -> ptm0
Jul 25 04:01:36 daemon warn kernel: BCMVLAN : ptm0 mode was set to RG
Jul 25 04:01:36 daemon info kernel: device ptm0 entered promiscuous mode
Jul 25 04:01:36 daemon notice syslog: pppd:cms logging initialized.
Jul 25 04:01:36 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jul 25 04:01:36 daemon notice syslog: PPP: Start to connect ...
Jul 25 04:02:03 daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected
Jul 25 04:02:03 daemon notice syslog: pppd:Couldn't reset tty to normal line discipline: Inappropriate ioctl for device
Jul 25 04:02:03 daemon notice syslog: pppd:Doing disconnect
Jul 25 04:02:06 daemon notice syslog: PPP: Start to connect ...
Jul 25 04:02:10 daemon crit syslog: PPP server detected.
Jul 25 04:02:11 daemon crit syslog: PPP session established.
Jul 25 04:02:11 daemon warn kernel: netdev path : ppp1.1 -> ptm0.1 -> ptm0
Jul 25 04:02:11 daemon notice syslog: pppd:Using interface ppp1.1
Jul 25 04:02:11 daemon notice syslog: pppd:Connect: ppp1.1 <--> ptm0.1
Jul 25 04:02:11 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:02:11 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:02:11 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:02:11 daemon crit syslog: PPP LCP UP.
Jul 25 04:02:11 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:02:11 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:02:11 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:02:11 daemon crit syslog: PPP LCP UP.
Jul 25 04:02:12 daemon notice syslog: pppd:local IP address 195.166.144.83
Jul 25 04:02:12 daemon notice syslog: pppd:remote IP address 195.166.130.138
Jul 25 04:02:12 daemon notice syslog: pppd:primary DNS address 212.159.6.10
Jul 25 04:02:12 daemon notice syslog: pppd:secondary DNS address 212.159.6.9
Jul 25 04:02:12 daemon crit syslog: Received valid IP address from server. Connection UP.
Jul 25 04:02:15 daemon warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache flushing the flows^[[0m
Jul 25 04:45:27 daemon notice syslog: pppd:LCP terminated by peer
Jul 25 04:45:27 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
Jul 25 04:45:27 daemon crit syslog: Clear IP addresses. Connection DOWN.
Jul 25 04:45:27 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:45:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:30 daemon notice syslog: pppd:Connection terminated.
Jul 25 04:45:30 daemon notice syslog: pppd:Connect time 43.3 minutes.
Jul 25 04:45:30 daemon notice syslog: pppd:Sent 67865 bytes, received 1576661 bytes.
Jul 25 04:45:30 daemon notice syslog: pppd:Doing disconnect
Jul 25 04:45:33 daemon notice syslog: PPP: Start to connect ...
Jul 25 04:45:37 daemon crit syslog: PPP server detected.
Jul 25 04:45:37 daemon crit syslog: PPP session established.
Jul 25 04:45:37 daemon warn kernel: netdev path : ppp1.1 -> ptm0.1 -> ptm0
Jul 25 04:45:37 daemon notice syslog: pppd:Using interface ppp1.1
Jul 25 04:45:37 daemon notice syslog: pppd:Connect: ppp1.1 <--> ptm0.1
Jul 25 04:45:37 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:45:37 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:37 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:37 daemon crit syslog: PPP LCP UP.
Jul 25 04:45:38 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:45:38 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:38 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:38 daemon crit syslog: PPP LCP UP.
Jul 25 04:45:48 daemon notice syslog: pppd:IPCP: timeout sending Config-Requests
Jul 25 04:45:48 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:45:48 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:48 daemon notice syslog: pppd:Connection terminated.
Jul 25 04:45:48 daemon notice syslog: pppd:Doing disconnect
Jul 25 04:45:51 daemon notice syslog: PPP: Start to connect ...
Jul 25 04:45:55 daemon crit syslog: PPP server detected.
Jul 25 04:45:55 daemon crit syslog: PPP session established.
Jul 25 04:45:55 daemon warn kernel: netdev path : ppp1.1 -> ptm0.1 -> ptm0
Jul 25 04:45:55 daemon notice syslog: pppd:Using interface ppp1.1
Jul 25 04:45:55 daemon notice syslog: pppd:Connect: ppp1.1 <--> ptm0.1
Jul 25 04:45:55 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:45:55 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:55 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:55 daemon crit syslog: PPP LCP UP.
Jul 25 04:45:56 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jul 25 04:45:56 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:56 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jul 25 04:45:56 daemon crit syslog: PPP LCP UP.
Jul 25 04:45:57 daemon notice syslog: pppd:local IP address 46.208.116.32
Jul 25 04:45:57 daemon notice syslog: pppd:remote IP address 195.166.128.191
Jul 25 04:45:57 daemon notice syslog: pppd:primary DNS address 212.159.6.10
Jul 25 04:45:57 daemon notice syslog: pppd:secondary DNS address 212.159.6.9
Jul 25 04:45:57 daemon crit syslog: Received valid IP address from server. Connection UP.
Jul 25 04:46:00 daemon warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache flushing the flows^[[0m
Jul 25 04:46:00 daemon err syslog: dhcpd:udhcp server (v0.9.6) started

Cheers for the help. I will try and ring plusnet this morning.
Top
Post Reply

Return to “BiPAC 8800 series”