Anything About Billion For UK Users
https://www.forum.billion.uk.com/
Hi Billion_Fan, extracted this from DSLStats:
Your stats look fine, try to keep the router on, with out any restarts alsoharry66 wrote: ↑Tue Jan 09, 2018 1:32 pm Hi @billion_fan,
Are the stats below good or bad? I read the linked page - but still not sure...
Downstream Upstream
SNR Margin (dB) 6.4 15.3
Attenuation (dB) 13.6 0.0
Output Power (dBm) 13.0 3.8
Attainable Rate (Kbps) 79184 29051
Rate (Kbps) 78618 19999
Is there any other stats I need to share?
I am on a 76Mb package with PlusNet..
Many Thanks
Can you grab some screen shots of your stats from d7 (status >>> statistics >> xDSL) then load d5 firmware again and check the vectoring status if its the same it might be BT, if its different grab some screen shots and send over all over the stats, so I can show our engineers the stats off both firmwares (you might want to wait a day or so before switching firmware so DLM does not restrict your speeds)evansnp wrote: ↑Tue Jan 09, 2018 3:56 pmHi Billion_Fan, extracted this from DSLStats:
Vectoring status: 5 (VECT_UNCONFIGURED)
On d5, this was "1 (VECT_FULL)" or words to that effect, if I remember correctly.
Many thanksbillion_fan wrote: ↑Wed Jan 10, 2018 9:22 am Your stats look fine, try to keep the router on, with out any restarts also
Will do!billion_fan wrote: ↑Wed Jan 10, 2018 9:27 amCan you grab some screen shots of your stats from d7 (status >>> statistics >> xDSL) then load d5 firmware again and check the vectoring status if its the same it might be BT, if its different grab some screen shots and send over all over the stats, so I can show our engineers the stats off both firmwares (you might want to wait a day or so before switching firmware so DLM does not restrict your speeds)
Hi Billion_Fan.evansnp wrote: ↑Wed Jan 10, 2018 12:38 pmWill do!billion_fan wrote: ↑Wed Jan 10, 2018 9:27 amCan you grab some screen shots of your stats from d7 (status >>> statistics >> xDSL) then load d5 firmware again and check the vectoring status if its the same it might be BT, if its different grab some screen shots and send over all over the stats, so I can show our engineers the stats off both firmwares (you might want to wait a day or so before switching firmware so DLM does not restrict your speeds)
Code: Select all
Stats recorded 18 Jan 2018 14:56:38
DSLAM/MSAN type: BDCM:0xa48c / v0xa48c
Modem/router firmware: AnnexA version - A2pv6F039v.d26q_rc1a
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 0 hour 10 min 39 sec
Resyncs: 0 (since 18 Jan 2018 14:54:27)
Downstream Upstream
Line attenuation (dB): 14.3 0.0
Signal attenuation (dB): Not monitored
Connection speed (kbps): 79999 19999
SNR margin (dB): 20.1 15.5
Power (dBm): 13.8 5.4
Interleave depth: 16 1
INP: 48.00 0
G.INP: Enabled Not enabled
Vectoring status: 1 (VECT_FULL)
RSCorr/RS (%): 0.0000 0.0000
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 0 0Can you try loading the attached firmware and see if the vectoring is enabled. (as the norm, upgrade and reset back to factory default settings and before you configure the device again, check to see if vectoring is enabled and SNR showing a higher rate)