VPN Passthrough

[dgk123]

On the remote 7800DX - L2TP with IPSec server which I can log into from other locations fine. No site to site VPNs.

On the local (my) 7800DX - L2TP with IPSec server configured. No site to site VPNs. From here I can't connect to the remote 7800DX (or any other VPN servers) unless I do the trick with turning off NAT-T and turning it back on again, then connected while it restarts, or bypass the local 7800 completely.

[billion_fan]

On the remote 7800DX - L2TP with IPSec server which I can log into from other locations fine. No site to site VPNs.

On the local (my) 7800DX - L2TP with IPSec server configured. No site to site VPNs. From here I can't connect to the remote 7800DX (or any other VPN servers) unless I do the trick with turning off NAT-T and turning it back on again, then connected while it restarts, or bypass the local 7800 completely.

Got it, once I get a chance I will test it for you

[billion_fan]

On the remote 7800DX - L2TP with IPSec server which I can log into from other locations fine. No site to site VPNs.

On the local (my) 7800DX - L2TP with IPSec server configured. No site to site VPNs. From here I can't connect to the remote 7800DX (or any other VPN servers) unless I do the trick with turning off NAT-T and turning it back on again, then connected while it restarts, or bypass the local 7800 completely.

Issue has been reported and we are discussing with our engineers.

[dgk123]

Many thanks, much appreciated.

[billion_fan]

Many thanks, much appreciated.

Can you confirm that if you disbale NAT- T, that you dial out to your office 7800DX using L2TP over IPsec??

[swampylee]

Hi, I've just raised a ticket for a similar sounding issue to the original poster. Just upgraded from a 7800n to a 7800dxl and since the upgrade my Cisco VPN client on Win 7 64bit refuses to connect to my corporate VPN. I'm able to ping the VPN IP address without a problem. Apparently the Cisco VPN software uses ipsec/UDP.

I'm using the latest 2.32d.dh2 firmware.

Was there ever a resolution to this original post? If I can't get this sorted out the 7800dxl is going to unfortunately have to go back.

Any help greatly appreciated.
-Lee

[billion_fan]

Hi, I've just raised a ticket for a similar sounding issue to the original poster. Just upgraded from a 7800n to a 7800dxl and since the upgrade my Cisco VPN client on Win 7 64bit refuses to connect to my corporate VPN. I'm able to ping the VPN IP address without a problem. Apparently the Cisco VPN software uses ipsec/UDP.

I'm using the latest 2.32d.dh2 firmware.

Was there ever a resolution to this original post? If I can't get this sorted out the 7800dxl is going to unfortunately have to go back.

Any help greatly appreciated.
-Lee

We have received your ticket, we will be in contact via our support ticket

[swampylee]

Just in case anyone else has the same problem, I was able to get around it by changing the config of the Cisco VPN client under "Enable Transparent Tunnelling" option from IPSec over UDP (NAT / PAT) to IPSec over TCP (Port 10000). I used IPSec over UDP for the last 2+ years with a 7800n so would still like Billion support to investigate why this had to be changed with the 7800dxl. It seems that the router is doing something strange when using IPSec over UDP.
Anyway, hopefully one day the above will help someone with the same issue.
-Lee

Hi, I've just raised a ticket for a similar sounding issue to the original poster. Just upgraded from a 7800n to a 7800dxl and since the upgrade my Cisco VPN client on Win 7 64bit refuses to connect to my corporate VPN. I'm able to ping the VPN IP address without a problem. Apparently the Cisco VPN software uses ipsec/UDP.

I'm using the latest 2.32d.dh2 firmware.

Was there ever a resolution to this original post? If I can't get this sorted out the 7800dxl is going to unfortunately have to go back.

Any help greatly appreciated.
-Lee

We have received your ticket, we will be in contact via our support ticket

[billion_fan]

Just in case anyone else has the same problem, I was able to get around it by changing the config of the Cisco VPN client under "Enable Transparent Tunnelling" option from IPSec over UDP (NAT / PAT) to IPSec over TCP (Port 10000). I used IPSec over UDP for the last 2+ years with a 7800n so would still like Billion support to investigate why this had to be changed with the 7800dxl. It seems that the router is doing something strange when using IPSec over UDP.
Anyway, hopefully one day the above will help someone with the same issue.
-Lee

Hi, I've just raised a ticket for a similar sounding issue to the original poster. Just upgraded from a 7800n to a 7800dxl and since the upgrade my Cisco VPN client on Win 7 64bit refuses to connect to my corporate VPN. I'm able to ping the VPN IP address without a problem. Apparently the Cisco VPN software uses ipsec/UDP.

I'm using the latest 2.32d.dh2 firmware.

Was there ever a resolution to this original post? If I can't get this sorted out the 7800dxl is going to unfortunately have to go back.

Any help greatly appreciated.
-Lee

We have received your ticket, we will be in contact via our support ticket

admin is looking into the issue, he will drop you update via our support ticket

[billion_fan]

Just in case anyone else has the same problem, I was able to get around it by changing the config of the Cisco VPN client under "Enable Transparent Tunnelling" option from IPSec over UDP (NAT / PAT) to IPSec over TCP (Port 10000). I used IPSec over UDP for the last 2+ years with a 7800n so would still like Billion support to investigate why this had to be changed with the 7800dxl. It seems that the router is doing something strange when using IPSec over UDP.
Anyway, hopefully one day the above will help someone with the same issue.
-Lee

Hi, I've just raised a ticket for a similar sounding issue to the original poster. Just upgraded from a 7800n to a 7800dxl and since the upgrade my Cisco VPN client on Win 7 64bit refuses to connect to my corporate VPN. I'm able to ping the VPN IP address without a problem. Apparently the Cisco VPN software uses ipsec/UDP.

I'm using the latest 2.32d.dh2 firmware.

Was there ever a resolution to this original post? If I can't get this sorted out the 7800dxl is going to unfortunately have to go back.

Any help greatly appreciated.
-Lee

We have received your ticket, we will be in contact via our support ticket

Try the attached firmware for the DXL and let us know if you have any issues with IPsec passthrough when using 'IPSec over UDP (NAT / PAT)'