Billion UK Forum

Just checked the system log foor the 8800nl r2 does anyone know what all this means states something aboout the broadcom is learning? Just want to know if it's anything to worry about. and whos Phillip Lougher?

Jan 1 00:00:14 kern info kernel: bcm_tstamp initialized, (hpt_freq=300000000 2us_div=300 2ns_mult=0 2ns_shift=0)
Jan 1 00:00:14 kern info kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan 1 00:00:14 kern info kernel: fuse init (API version 7.18)
Jan 1 00:00:14 kern info kernel: msgmni has been set to 115
Jan 1 00:00:14 kern info kernel: io scheduler noop registered (default)
Jan 1 00:00:14 kern warn kernel: bcm963xx_mtd driver
Jan 1 00:00:14 kern warn kernel: File system address: 0xb8010100
Jan 1 00:00:14 kern warn kernel: Registered device mtd:rootfs dev0 Address=0xb8010100 Size=8826880
Jan 1 00:00:14 kern info kernel: PPP generic driver version 2.4.2
Jan 1 00:00:14 kern info kernel: PPP BSD Compression module registered
Jan 1 00:00:14 kern info kernel: PPP Deflate Compression module registered
Jan 1 00:00:14 kern info kernel: NET: Registered protocol family 24
Jan 1 00:00:14 kern info kernel: Initializing USB Mass Storage driver...
Jan 1 00:00:14 kern info kernel: usbcore: registered new interface driver usb-storage
Jan 1 00:00:14 kern info kernel: USB Mass Storage support registered.
Jan 1 00:00:14 kern warn kernel: brcmboard: brcm_board_init entry
Jan 1 00:00:14 kern warn kernel: SES: Button Interrupt 0x1 is enabled
Jan 1 00:00:14 kern warn kernel: SES: LED GPIO 0x1 is enabled
Jan 1 00:00:14 kern warn kernel: DYING GASP IRQ initialized
Jan 1 00:00:14 kern info kernel: Serial: BCM63XX driver $Revision: 3.00 $
Jan 1 00:00:14 kern info kernel: ^[[0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)^[[0m
Jan 1 00:00:14 kern info kernel: ttyS0 at MMIO 0xb0000280 (irq = 8) is a BCM63XX
Jan 1 00:00:14 kern info kernel: ttyS1 at MMIO 0xb00002a0 (irq = 9) is a BCM63XX
Jan 1 00:00:14 kern warn kernel: Total # RxBds=2812
Jan 1 00:00:14 kern warn kernel: bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
Jan 1 00:00:14 kern info kernel: GACT probability NOT on
Jan 1 00:00:14 kern info kernel: Mirror/redirect action on
Jan 1 00:00:14 kern info kernel: u32 classifier
Jan 1 00:00:14 kern info kernel: input device check on
Jan 1 00:00:14 kern info kernel: Actions configured
Jan 1 00:00:14 kern info kernel: TCP: cubic registered
Jan 1 00:00:14 kern info kernel: Initializing XFRM netlink socket
Jan 1 00:00:14 kern warn kernel: usb r:0
Jan 1 00:00:14 kern warn kernel: chipinfo: module license 'proprietary' taints kernel.
Jan 1 00:00:14 kern warn kernel: Disabling lock debugging due to kernel taint
Jan 1 00:00:14 kern warn kernel: brcmchipinfo: brcm_chipinfo_init entry
Jan 1 00:00:14 kern warn kernel: bcmxtmrt: Broadcom BCM3381B0 ATM/PTM Network Device v0.6 Feb 20 2017 18:06:20
Jan 1 00:00:14 kern warn kernel: Broadcom Ingress QoS Module Char Driver v0.1 Feb 20 2017 18:05:51 Registered<243>^[[0m
Jan 1 00:00:14 kern warn kernel: Broadcom Ingress QoS ver 0.1 initialized
Jan 1 00:00:14 kern warn kernel: BPM: tot_mem_size=67108864B (64MB), buf_mem_size <15%> =10066320B (9MB), num of buffers=4993, buf size=2016
Jan 1 00:00:14 kern warn kernel: Broadcom BPM Module Char Driver v0.1 Feb 20 2017 18:05:50 Registered<244>^[[0m
Jan 1 00:00:14 kern warn kernel: NBUFF v1.0 Initialized
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mInitialized fcache state^[[0m
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache Char Driver v2.2 Feb 20 2017 18:05:51 Registered<242>^[[0m
Jan 1 00:00:14 kern warn kernel: Created Proc FS /procfs/fcache
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache registered with netdev chain^[[0m
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.^[[0m
Jan 1 00:00:14 kern warn kernel: flwStatsThread created
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mConstructed Broadcom Packet Flow Cache v2.2 Feb 20 2017 18:05:51^[[0m
Jan 1 00:00:14 kern warn kernel: bcmxtmcfg: bcmxtmcfg_init entry
Jan 1 00:00:14 kern warn kernel: adsl: adsl_init entry
Jan 1 00:00:14 kern warn kernel: Broadcom BCM63381B0 Ethernet Network Device v0.1 Feb 20 2017 18:06:12
Jan 1 00:00:14 kern warn kernel: ETH Init: Ch:0 - 200 tx BDs at 0xa3b0f000
Jan 1 00:00:14 kern warn kernel: ETH Init: Ch:0 - 1997 rx BDs at 0xa2a90000
Jan 1 00:00:14 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Jan 1 00:00:14 kern warn kernel: eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth4: <Int sw port: 4> <Logical : 04> PHY_ID <0x05180018 : 0x18> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: Ethernet Auto Power Down and Sleep: Enabled
Jan 1 00:00:14 kern info kernel: NComm TMS V6.80 Kernel Module loaded.
Jan 1 00:00:14 kern info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: EHCI Host Controller
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:14 kern warn kernel: ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: irq 113, io mem 0x1000c300
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
Jan 1 00:00:14 kern info kernel: hub 1-0:1.0: 1 port detected
Jan 1 00:00:14 kern info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: irq 112, io mem 0x1000c400
Jan 1 00:00:14 kern info kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:14 kern info kernel: hub 2-0:1.0: 1 port detected
Jan 1 00:00:14 kern info kernel: usbcore: registered new interface driver usblp
Jan 1 00:00:14 kern info kernel: Initializing WLCSM Module
Jan 1 00:00:14 kern info kernel: WLCSM Module loaded successfully
Jan 1 00:00:14 kern warn kernel: --SMP support
Jan 1 00:00:14 kern warn kernel: wl: dsl_tx_pkt_flush_len=338
Jan 1 00:00:14 kern warn kernel: wl: norm_wmark_tot=1417, pktc_wmark_tot=1417
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan 1 00:00:14 kern warn kernel: wl: passivemode=1
Jan 1 00:00:14 kern info kernel: wl0: creating kthread wl0-kthrd
Jan 1 00:00:14 kern warn kernel: wl: napimode=0
Jan 1 00:00:14 kern warn kernel: initvars_cis_pci: Not CIS format
Jan 1 00:00:14 kern warn kernel: Neither SPROM nor OTP has valid image
Jan 1 00:00:14 kern warn kernel: wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
Jan 1 00:00:14 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:14 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:14 kern warn kernel: wl: loading /etc/wlan/bcm43217_map.bin
Jan 1 00:00:14 kern warn kernel: srom rev:8
Jan 1 00:00:14 kern warn kernel: wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
Jan 1 00:00:14 kern warn kernel: wl0: allocskbmode=1 currallocskbsz=256
Jan 1 00:00:14 kern warn kernel: wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.43.21.cpe4.16L02A.0-kdb
Jan 1 00:00:14 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:14 kern warn kernel: p8021ag: p8021ag_init entry
Jan 1 00:00:14 kern info kernel: Broadcom 802.1Q VLAN Interface, v0.1
Jan 1 00:00:14 kern warn kernel: Host MIPS Clock divider pwrsaving is enabled
Jan 1 00:00:14 kern info kernel: Netfilter messages via NETLINK v0.30.
Jan 1 00:00:15 kern warn kernel: br_netlink_mcpd.c: Setting registration type 0 pid to 474
Jan 1 00:00:16 kern info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:16 kern info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:17 kern info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:17 kern info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:20 kern info kernel: device eth1 entered promiscuous mode
Jan 1 00:00:20 kern info kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:23 kern info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:23 kern info kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready
Jan 1 00:00:25 kern info kernel: device eth3 entered promiscuous mode
Jan 1 00:00:25 kern info kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
Jan 1 00:00:28 kern info kernel: device eth4 entered promiscuous mode
Jan 1 00:00:28 kern info kernel: ADDRCONF(NETDEV_UP): eth4: link is not ready
Jan 1 00:00:31 kern warn kernel: *** dslThread dslPid=802
Jan 1 00:00:31 kern warn kernel: BcmAdsl_Initialize=0xC0137050, g_pFnNotifyCallback=0xC0171300
Jan 1 00:00:31 kern warn kernel: pSdramPHY=0xA3FFFFF8, 0x409E48DA 0x725A5B4A
Jan 1 00:00:31 kern warn kernel: *** XfaceOffset: 0x4FF90 => 0x4FF90 ***
Jan 1 00:00:31 kern warn kernel: *** PhySdramSize got adjusted: 0xF546C => 0x123A78 ***
Jan 1 00:00:31 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=58720(58720)
Jan 1 00:00:31 kern warn kernel: AdslCoreHwReset: pLocSbSta=814f8000 bkupThreshold=3072
Jan 1 00:00:31 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB4E74
Jan 1 00:00:31 kern warn kernel: VersionInfo: A2pvI042e.d26g
Jan 1 00:00:31 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:31 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:31 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa25fa000
Jan 1 00:00:31 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa2a62580
Jan 1 00:00:31 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 82541d04
Jan 1 00:00:32 kern info kernel: nf_conntrack version 0.5.0 (923 buckets, 3692 max)
Jan 1 00:00:33 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:34 kern info kernel: monitor task is initialized pid= 435
Jan 1 00:00:35 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:36 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:01:02 kern crit kernel: Line 0: VDSL G.993 channel analysis
Jan 1 00:01:03 kern crit kernel: Line 0: VDSL2 link up, Bearer 0, us=19999, ds=74000
Jan 1 00:01:03 kern crit kernel: Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:03 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:03 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e df 0b
Jan 1 00:01:03 kern warn kernel: [DoCreateDeviceReq.710]: register_netdev
Jan 1 00:01:03 kern warn kernel: [DoCreateDeviceReq.712]: register_netdev done
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:03 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa0d06000
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=19999000, DS=74000000
Jan 1 00:01:03 kern info kernel: NComm Ethernet 802.3AH OA&M loaded.
Jan 1 00:01:03 kern info kernel: NComm Ethernet 802.1AG OA&M loaded.
Jan 1 00:01:04 kern warn kernel: netdev path : ptm0.1
Jan 1 00:01:04 kern info kernel: ->
Jan 1 00:01:04 kern info kernel: ptm0
Jan 1 00:01:04 kern warn kernel: BCMVLAN : ptm0 mode was set to RG
Jan 1 00:01:04 kern info kernel: device ptm0.1 entered promiscuous mode
Jan 1 00:01:04 kern info kernel: device ptm0 entered promiscuous mode
Jan 1 00:01:04 kern info kernel: br0: port 6(ptm0.1) entered forwarding state
Jan 1 00:01:04 kern info kernel: br0: port 6(ptm0.1) entered forwarding state
Jan 1 00:01:16 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link UP 100 mbps full duplex
Jan 1 00:01:16 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Jan 1 00:01:16 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:16 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:17 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:17 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:01:17 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:17 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:19 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link DOWN.
Jan 1 00:01:19 kern info kernel: br0: port 4(eth3) entered disabled state
Jan 1 00:01:21 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link DOWN.
Jan 1 00:01:21 kern info kernel: br0: port 5(eth4) entered disabled state
Jan 1 00:01:23 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link UP 100 mbps full duplex
Jan 1 00:01:23 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:23 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:25 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:25 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:25 kern info kernel: br0: port 5(eth4) entered forwarding state

Here's my stats dooes everything look alright here?

adsl info --stats
adsl: ADSL driver and PHY status
Status: Showtime
Last Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 29351 Kbps, Downstream rate = 87344 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 74000 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 9.2 15.5
Attn(dB): 11.3 0.0
Pwr(dBm): 12.6 -0.8

VDSL2 framing
Bearer 0
MSGc: -6 26
B: 174 237
M: 1 1
T: 0 42
R: 8 16
S: 0.0752 0.3781
L: 19456 5374
D: 16 1
I: 183 127
N: 183 254
Q: 16 0
V: 3 0
RxQueue: 42 0
TxQueue: 14 0
G.INP Framing: 18 0
G.INP lookback: 14 0
RRC bits: 0 24
Bearer 1
MSGc: 154 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 6.4000 0.0000
L: 40 0
D: 3 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0

Counters
Bearer 0
OHF: 0 1043011
OHFErr: 36 1336
RS: 4045447744 1105875
RSCorr: 109459 20407
RSUnCorr: 0 0
Bearer 1
OHF: 75452513 0
OHFErr: 29 0
RS: 754524513 0
RSCorr: 766 0
RSUnCorr: 51 0

Retransmit Counters
rtx_tx: 221113 0
rtx_c: 1575 0
rtx_uc: 3282 0

G.INP Counters
LEFTRS: 21 0
minEFTR: 73983 0
errFreeBits: 1367662848 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 671560615 0
Data Cells: 4148489109 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 8 928
SES: 0 18
UAS: 32 32
AS: 1212101

Bearer 0
INP: 49.00 0.00
INPRein: 0.00 0.00
delay: 0 0
PER: 0.00 3.98
OR: 0.01 64.22
AgR: 74132.27 20063.54

Bearer 1
INP: 4.50 0.00
INPRein: 4.50 0.00
delay: 3 0
PER: 16.06 0.01
OR: 79.68 0.01
AgR: 79.68 0.01

Bitswap: 4729/4740 454/454

Total time = 14 days 42 min 13 sec
FEC: 109459 20407
CRC: 36 1336
ES: 8 928
SES: 0 18
UAS: 32 32
LOS: 0 0
LOF: 0 0
LOM: 0 0
Retr: 0
Latest 15 minutes time = 12 min 13 sec
FEC: 25 4
CRC: 0 1
ES: 0 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Retr: 0
Previous 15 minutes time = 15 min 0 sec
FEC: 79 4
CRC: 0 1
ES: 0 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Retr: N/A
Latest 1 day time = 42 min 13 sec
FEC: 201 8
CRC: 0 2
ES: 0 2
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Retr: 0
Previous 1 day time = 24 hours 0 sec
FEC: 5133 272
CRC: 0 71
ES: 0 57
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Retr: 0
Since Link time = 14 days 41 min 39 sec
FEC: 109459 20407
CRC: 36 1336
ES: 8 928
SES: 0 18
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Retr: 0
NTR: mipsCntAtNtr=0 ncoCntAtNtr=0
>

nfxcr3w wrote:Just checked the system log foor the 8800nl r2 does anyone know what all this means states something aboout the broadcom is learning? Just want to know if it's anything to worry about. and whos Phillip Lougher?

Jan 1 00:00:14 kern info kernel: bcm_tstamp initialized, (hpt_freq=300000000 2us_div=300 2ns_mult=0 2ns_shift=0)
Jan 1 00:00:14 kern info kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan 1 00:00:14 kern info kernel: fuse init (API version 7.18)
Jan 1 00:00:14 kern info kernel: msgmni has been set to 115
Jan 1 00:00:14 kern info kernel: io scheduler noop registered (default)
Jan 1 00:00:14 kern warn kernel: bcm963xx_mtd driver
Jan 1 00:00:14 kern warn kernel: File system address: 0xb8010100
Jan 1 00:00:14 kern warn kernel: Registered device mtd:rootfs dev0 Address=0xb8010100 Size=8826880
Jan 1 00:00:14 kern info kernel: PPP generic driver version 2.4.2
Jan 1 00:00:14 kern info kernel: PPP BSD Compression module registered
Jan 1 00:00:14 kern info kernel: PPP Deflate Compression module registered
Jan 1 00:00:14 kern info kernel: NET: Registered protocol family 24
Jan 1 00:00:14 kern info kernel: Initializing USB Mass Storage driver...
Jan 1 00:00:14 kern info kernel: usbcore: registered new interface driver usb-storage
Jan 1 00:00:14 kern info kernel: USB Mass Storage support registered.
Jan 1 00:00:14 kern warn kernel: brcmboard: brcm_board_init entry
Jan 1 00:00:14 kern warn kernel: SES: Button Interrupt 0x1 is enabled
Jan 1 00:00:14 kern warn kernel: SES: LED GPIO 0x1 is enabled
Jan 1 00:00:14 kern warn kernel: DYING GASP IRQ initialized
Jan 1 00:00:14 kern info kernel: Serial: BCM63XX driver $Revision: 3.00 $
Jan 1 00:00:14 kern info kernel: ^[[0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)^[[0m
Jan 1 00:00:14 kern info kernel: ttyS0 at MMIO 0xb0000280 (irq = 8) is a BCM63XX
Jan 1 00:00:14 kern info kernel: ttyS1 at MMIO 0xb00002a0 (irq = 9) is a BCM63XX
Jan 1 00:00:14 kern warn kernel: Total # RxBds=2812
Jan 1 00:00:14 kern warn kernel: bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
Jan 1 00:00:14 kern info kernel: GACT probability NOT on
Jan 1 00:00:14 kern info kernel: Mirror/redirect action on
Jan 1 00:00:14 kern info kernel: u32 classifier
Jan 1 00:00:14 kern info kernel: input device check on
Jan 1 00:00:14 kern info kernel: Actions configured
Jan 1 00:00:14 kern info kernel: TCP: cubic registered
Jan 1 00:00:14 kern info kernel: Initializing XFRM netlink socket
Jan 1 00:00:14 kern warn kernel: usb r:0
Jan 1 00:00:14 kern warn kernel: chipinfo: module license 'proprietary' taints kernel.
Jan 1 00:00:14 kern warn kernel: Disabling lock debugging due to kernel taint
Jan 1 00:00:14 kern warn kernel: brcmchipinfo: brcm_chipinfo_init entry
Jan 1 00:00:14 kern warn kernel: bcmxtmrt: Broadcom BCM3381B0 ATM/PTM Network Device v0.6 Feb 20 2017 18:06:20
Jan 1 00:00:14 kern warn kernel: Broadcom Ingress QoS Module Char Driver v0.1 Feb 20 2017 18:05:51 Registered<243>^[[0m
Jan 1 00:00:14 kern warn kernel: Broadcom Ingress QoS ver 0.1 initialized
Jan 1 00:00:14 kern warn kernel: BPM: tot_mem_size=67108864B (64MB), buf_mem_size <15%> =10066320B (9MB), num of buffers=4993, buf size=2016
Jan 1 00:00:14 kern warn kernel: Broadcom BPM Module Char Driver v0.1 Feb 20 2017 18:05:50 Registered<244>^[[0m
Jan 1 00:00:14 kern warn kernel: NBUFF v1.0 Initialized
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mInitialized fcache state^[[0m
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache Char Driver v2.2 Feb 20 2017 18:05:51 Registered<242>^[[0m
Jan 1 00:00:14 kern warn kernel: Created Proc FS /procfs/fcache
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache registered with netdev chain^[[0m
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.^[[0m
Jan 1 00:00:14 kern warn kernel: flwStatsThread created
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mConstructed Broadcom Packet Flow Cache v2.2 Feb 20 2017 18:05:51^[[0m
Jan 1 00:00:14 kern warn kernel: bcmxtmcfg: bcmxtmcfg_init entry
Jan 1 00:00:14 kern warn kernel: adsl: adsl_init entry
Jan 1 00:00:14 kern warn kernel: Broadcom BCM63381B0 Ethernet Network Device v0.1 Feb 20 2017 18:06:12
Jan 1 00:00:14 kern warn kernel: ETH Init: Ch:0 - 200 tx BDs at 0xa3b0f000
Jan 1 00:00:14 kern warn kernel: ETH Init: Ch:0 - 1997 rx BDs at 0xa2a90000
Jan 1 00:00:14 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Jan 1 00:00:14 kern warn kernel: eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth4: <Int sw port: 4> <Logical : 04> PHY_ID <0x05180018 : 0x18> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: Ethernet Auto Power Down and Sleep: Enabled
Jan 1 00:00:14 kern info kernel: NComm TMS V6.80 Kernel Module loaded.
Jan 1 00:00:14 kern info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: EHCI Host Controller
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:14 kern warn kernel: ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: irq 113, io mem 0x1000c300
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
Jan 1 00:00:14 kern info kernel: hub 1-0:1.0: 1 port detected
Jan 1 00:00:14 kern info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: irq 112, io mem 0x1000c400
Jan 1 00:00:14 kern info kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:14 kern info kernel: hub 2-0:1.0: 1 port detected
Jan 1 00:00:14 kern info kernel: usbcore: registered new interface driver usblp
Jan 1 00:00:14 kern info kernel: Initializing WLCSM Module
Jan 1 00:00:14 kern info kernel: WLCSM Module loaded successfully
Jan 1 00:00:14 kern warn kernel: --SMP support
Jan 1 00:00:14 kern warn kernel: wl: dsl_tx_pkt_flush_len=338
Jan 1 00:00:14 kern warn kernel: wl: norm_wmark_tot=1417, pktc_wmark_tot=1417
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan 1 00:00:14 kern warn kernel: wl: passivemode=1
Jan 1 00:00:14 kern info kernel: wl0: creating kthread wl0-kthrd
Jan 1 00:00:14 kern warn kernel: wl: napimode=0
Jan 1 00:00:14 kern warn kernel: initvars_cis_pci: Not CIS format
Jan 1 00:00:14 kern warn kernel: Neither SPROM nor OTP has valid image
Jan 1 00:00:14 kern warn kernel: wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
Jan 1 00:00:14 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:14 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:14 kern warn kernel: wl: loading /etc/wlan/bcm43217_map.bin
Jan 1 00:00:14 kern warn kernel: srom rev:8
Jan 1 00:00:14 kern warn kernel: wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
Jan 1 00:00:14 kern warn kernel: wl0: allocskbmode=1 currallocskbsz=256
Jan 1 00:00:14 kern warn kernel: wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.43.21.cpe4.16L02A.0-kdb
Jan 1 00:00:14 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:14 kern warn kernel: p8021ag: p8021ag_init entry
Jan 1 00:00:14 kern info kernel: Broadcom 802.1Q VLAN Interface, v0.1
Jan 1 00:00:14 kern warn kernel: Host MIPS Clock divider pwrsaving is enabled
Jan 1 00:00:14 kern info kernel: Netfilter messages via NETLINK v0.30.
Jan 1 00:00:15 kern warn kernel: br_netlink_mcpd.c: Setting registration type 0 pid to 474
Jan 1 00:00:16 kern info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:16 kern info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:17 kern info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:17 kern info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:20 kern info kernel: device eth1 entered promiscuous mode
Jan 1 00:00:20 kern info kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:23 kern info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:23 kern info kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready
Jan 1 00:00:25 kern info kernel: device eth3 entered promiscuous mode
Jan 1 00:00:25 kern info kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
Jan 1 00:00:28 kern info kernel: device eth4 entered promiscuous mode
Jan 1 00:00:28 kern info kernel: ADDRCONF(NETDEV_UP): eth4: link is not ready
Jan 1 00:00:31 kern warn kernel: *** dslThread dslPid=802
Jan 1 00:00:31 kern warn kernel: BcmAdsl_Initialize=0xC0137050, g_pFnNotifyCallback=0xC0171300
Jan 1 00:00:31 kern warn kernel: pSdramPHY=0xA3FFFFF8, 0x409E48DA 0x725A5B4A
Jan 1 00:00:31 kern warn kernel: *** XfaceOffset: 0x4FF90 => 0x4FF90 ***
Jan 1 00:00:31 kern warn kernel: *** PhySdramSize got adjusted: 0xF546C => 0x123A78 ***
Jan 1 00:00:31 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=58720(58720)
Jan 1 00:00:31 kern warn kernel: AdslCoreHwReset: pLocSbSta=814f8000 bkupThreshold=3072
Jan 1 00:00:31 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB4E74
Jan 1 00:00:31 kern warn kernel: VersionInfo: A2pvI042e.d26g
Jan 1 00:00:31 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:31 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:31 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa25fa000
Jan 1 00:00:31 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa2a62580
Jan 1 00:00:31 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 82541d04
Jan 1 00:00:32 kern info kernel: nf_conntrack version 0.5.0 (923 buckets, 3692 max)
Jan 1 00:00:33 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:34 kern info kernel: monitor task is initialized pid= 435
Jan 1 00:00:35 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:36 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:01:02 kern crit kernel: Line 0: VDSL G.993 channel analysis
Jan 1 00:01:03 kern crit kernel: Line 0: VDSL2 link up, Bearer 0, us=19999, ds=74000
Jan 1 00:01:03 kern crit kernel: Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:03 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:03 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e df 0b
Jan 1 00:01:03 kern warn kernel: [DoCreateDeviceReq.710]: register_netdev
Jan 1 00:01:03 kern warn kernel: [DoCreateDeviceReq.712]: register_netdev done
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:03 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa0d06000
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=19999000, DS=74000000
Jan 1 00:01:03 kern info kernel: NComm Ethernet 802.3AH OA&M loaded.
Jan 1 00:01:03 kern info kernel: NComm Ethernet 802.1AG OA&M loaded.
Jan 1 00:01:04 kern warn kernel: netdev path : ptm0.1
Jan 1 00:01:04 kern info kernel: ->
Jan 1 00:01:04 kern info kernel: ptm0
Jan 1 00:01:04 kern warn kernel: BCMVLAN : ptm0 mode was set to RG
Jan 1 00:01:04 kern info kernel: device ptm0.1 entered promiscuous mode
Jan 1 00:01:04 kern info kernel: device ptm0 entered promiscuous mode
Jan 1 00:01:04 kern info kernel: br0: port 6(ptm0.1) entered forwarding state
Jan 1 00:01:04 kern info kernel: br0: port 6(ptm0.1) entered forwarding state
Jan 1 00:01:16 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link UP 100 mbps full duplex
Jan 1 00:01:16 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Jan 1 00:01:16 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:16 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:17 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:17 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:01:17 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:17 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:19 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link DOWN.
Jan 1 00:01:19 kern info kernel: br0: port 4(eth3) entered disabled state
Jan 1 00:01:21 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link DOWN.
Jan 1 00:01:21 kern info kernel: br0: port 5(eth4) entered disabled state
Jan 1 00:01:23 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link UP 100 mbps full duplex
Jan 1 00:01:23 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:23 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:25 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:25 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:25 kern info kernel: br0: port 5(eth4) entered forwarding state

Nothing to worry about, just normal Broadcom logs (the chipset vendor of the router),

billion_fan wrote:

nfxcr3w wrote:Just checked the system log foor the 8800nl r2 does anyone know what all this means states something aboout the broadcom is learning? Just want to know if it's anything to worry about. and whos Phillip Lougher?

Jan 1 00:00:14 kern info kernel: bcm_tstamp initialized, (hpt_freq=300000000 2us_div=300 2ns_mult=0 2ns_shift=0)
Jan 1 00:00:14 kern info kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan 1 00:00:14 kern info kernel: fuse init (API version 7.18)
Jan 1 00:00:14 kern info kernel: msgmni has been set to 115
Jan 1 00:00:14 kern info kernel: io scheduler noop registered (default)
Jan 1 00:00:14 kern warn kernel: bcm963xx_mtd driver
Jan 1 00:00:14 kern warn kernel: File system address: 0xb8010100
Jan 1 00:00:14 kern warn kernel: Registered device mtd:rootfs dev0 Address=0xb8010100 Size=8826880
Jan 1 00:00:14 kern info kernel: PPP generic driver version 2.4.2
Jan 1 00:00:14 kern info kernel: PPP BSD Compression module registered
Jan 1 00:00:14 kern info kernel: PPP Deflate Compression module registered
Jan 1 00:00:14 kern info kernel: NET: Registered protocol family 24
Jan 1 00:00:14 kern info kernel: Initializing USB Mass Storage driver...
Jan 1 00:00:14 kern info kernel: usbcore: registered new interface driver usb-storage
Jan 1 00:00:14 kern info kernel: USB Mass Storage support registered.
Jan 1 00:00:14 kern warn kernel: brcmboard: brcm_board_init entry
Jan 1 00:00:14 kern warn kernel: SES: Button Interrupt 0x1 is enabled
Jan 1 00:00:14 kern warn kernel: SES: LED GPIO 0x1 is enabled
Jan 1 00:00:14 kern warn kernel: DYING GASP IRQ initialized
Jan 1 00:00:14 kern info kernel: Serial: BCM63XX driver $Revision: 3.00 $
Jan 1 00:00:14 kern info kernel: ^[[0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)^[[0m
Jan 1 00:00:14 kern info kernel: ttyS0 at MMIO 0xb0000280 (irq = 8) is a BCM63XX
Jan 1 00:00:14 kern info kernel: ttyS1 at MMIO 0xb00002a0 (irq = 9) is a BCM63XX
Jan 1 00:00:14 kern warn kernel: Total # RxBds=2812
Jan 1 00:00:14 kern warn kernel: bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
Jan 1 00:00:14 kern info kernel: GACT probability NOT on
Jan 1 00:00:14 kern info kernel: Mirror/redirect action on
Jan 1 00:00:14 kern info kernel: u32 classifier
Jan 1 00:00:14 kern info kernel: input device check on
Jan 1 00:00:14 kern info kernel: Actions configured
Jan 1 00:00:14 kern info kernel: TCP: cubic registered
Jan 1 00:00:14 kern info kernel: Initializing XFRM netlink socket
Jan 1 00:00:14 kern warn kernel: usb r:0
Jan 1 00:00:14 kern warn kernel: chipinfo: module license 'proprietary' taints kernel.
Jan 1 00:00:14 kern warn kernel: Disabling lock debugging due to kernel taint
Jan 1 00:00:14 kern warn kernel: brcmchipinfo: brcm_chipinfo_init entry
Jan 1 00:00:14 kern warn kernel: bcmxtmrt: Broadcom BCM3381B0 ATM/PTM Network Device v0.6 Feb 20 2017 18:06:20
Jan 1 00:00:14 kern warn kernel: Broadcom Ingress QoS Module Char Driver v0.1 Feb 20 2017 18:05:51 Registered<243>^[[0m
Jan 1 00:00:14 kern warn kernel: Broadcom Ingress QoS ver 0.1 initialized
Jan 1 00:00:14 kern warn kernel: BPM: tot_mem_size=67108864B (64MB), buf_mem_size <15%> =10066320B (9MB), num of buffers=4993, buf size=2016
Jan 1 00:00:14 kern warn kernel: Broadcom BPM Module Char Driver v0.1 Feb 20 2017 18:05:50 Registered<244>^[[0m
Jan 1 00:00:14 kern warn kernel: NBUFF v1.0 Initialized
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mInitialized fcache state^[[0m
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache Char Driver v2.2 Feb 20 2017 18:05:51 Registered<242>^[[0m
Jan 1 00:00:14 kern warn kernel: Created Proc FS /procfs/fcache
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache registered with netdev chain^[[0m
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.^[[0m
Jan 1 00:00:14 kern warn kernel: flwStatsThread created
Jan 1 00:00:14 kern warn kernel: ^[[0;36;44mConstructed Broadcom Packet Flow Cache v2.2 Feb 20 2017 18:05:51^[[0m
Jan 1 00:00:14 kern warn kernel: bcmxtmcfg: bcmxtmcfg_init entry
Jan 1 00:00:14 kern warn kernel: adsl: adsl_init entry
Jan 1 00:00:14 kern warn kernel: Broadcom BCM63381B0 Ethernet Network Device v0.1 Feb 20 2017 18:06:12
Jan 1 00:00:14 kern warn kernel: ETH Init: Ch:0 - 200 tx BDs at 0xa3b0f000
Jan 1 00:00:14 kern warn kernel: ETH Init: Ch:0 - 1997 rx BDs at 0xa2a90000
Jan 1 00:00:14 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Jan 1 00:00:14 kern warn kernel: eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: eth4: <Int sw port: 4> <Logical : 04> PHY_ID <0x05180018 : 0x18> MAC : 60:03:47:2E:DF:09
Jan 1 00:00:14 kern warn kernel: Ethernet Auto Power Down and Sleep: Enabled
Jan 1 00:00:14 kern info kernel: NComm TMS V6.80 Kernel Module loaded.
Jan 1 00:00:14 kern info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: EHCI Host Controller
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:14 kern warn kernel: ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: irq 113, io mem 0x1000c300
Jan 1 00:00:14 kern info kernel: ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
Jan 1 00:00:14 kern info kernel: hub 1-0:1.0: 1 port detected
Jan 1 00:00:14 kern info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
Jan 1 00:00:14 kern info kernel: ohci_hcd 0000:00:09.0: irq 112, io mem 0x1000c400
Jan 1 00:00:14 kern info kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:14 kern info kernel: hub 2-0:1.0: 1 port detected
Jan 1 00:00:14 kern info kernel: usbcore: registered new interface driver usblp
Jan 1 00:00:14 kern info kernel: Initializing WLCSM Module
Jan 1 00:00:14 kern info kernel: WLCSM Module loaded successfully
Jan 1 00:00:14 kern warn kernel: --SMP support
Jan 1 00:00:14 kern warn kernel: wl: dsl_tx_pkt_flush_len=338
Jan 1 00:00:14 kern warn kernel: wl: norm_wmark_tot=1417, pktc_wmark_tot=1417
Jan 1 00:00:14 kern warn kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan 1 00:00:14 kern warn kernel: wl: passivemode=1
Jan 1 00:00:14 kern info kernel: wl0: creating kthread wl0-kthrd
Jan 1 00:00:14 kern warn kernel: wl: napimode=0
Jan 1 00:00:14 kern warn kernel: initvars_cis_pci: Not CIS format
Jan 1 00:00:14 kern warn kernel: Neither SPROM nor OTP has valid image
Jan 1 00:00:14 kern warn kernel: wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
Jan 1 00:00:14 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:14 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:14 kern warn kernel: wl: loading /etc/wlan/bcm43217_map.bin
Jan 1 00:00:14 kern warn kernel: srom rev:8
Jan 1 00:00:14 kern warn kernel: wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
Jan 1 00:00:14 kern warn kernel: wl0: allocskbmode=1 currallocskbsz=256
Jan 1 00:00:14 kern warn kernel: wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.43.21.cpe4.16L02A.0-kdb
Jan 1 00:00:14 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:14 kern warn kernel: p8021ag: p8021ag_init entry
Jan 1 00:00:14 kern info kernel: Broadcom 802.1Q VLAN Interface, v0.1
Jan 1 00:00:14 kern warn kernel: Host MIPS Clock divider pwrsaving is enabled
Jan 1 00:00:14 kern info kernel: Netfilter messages via NETLINK v0.30.
Jan 1 00:00:15 kern warn kernel: br_netlink_mcpd.c: Setting registration type 0 pid to 474
Jan 1 00:00:16 kern info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:16 kern info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:17 kern info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:17 kern info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:20 kern info kernel: device eth1 entered promiscuous mode
Jan 1 00:00:20 kern info kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:23 kern info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:23 kern info kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready
Jan 1 00:00:25 kern info kernel: device eth3 entered promiscuous mode
Jan 1 00:00:25 kern info kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
Jan 1 00:00:28 kern info kernel: device eth4 entered promiscuous mode
Jan 1 00:00:28 kern info kernel: ADDRCONF(NETDEV_UP): eth4: link is not ready
Jan 1 00:00:31 kern warn kernel: *** dslThread dslPid=802
Jan 1 00:00:31 kern warn kernel: BcmAdsl_Initialize=0xC0137050, g_pFnNotifyCallback=0xC0171300
Jan 1 00:00:31 kern warn kernel: pSdramPHY=0xA3FFFFF8, 0x409E48DA 0x725A5B4A
Jan 1 00:00:31 kern warn kernel: *** XfaceOffset: 0x4FF90 => 0x4FF90 ***
Jan 1 00:00:31 kern warn kernel: *** PhySdramSize got adjusted: 0xF546C => 0x123A78 ***
Jan 1 00:00:31 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=58720(58720)
Jan 1 00:00:31 kern warn kernel: AdslCoreHwReset: pLocSbSta=814f8000 bkupThreshold=3072
Jan 1 00:00:31 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB4E74
Jan 1 00:00:31 kern warn kernel: VersionInfo: A2pvI042e.d26g
Jan 1 00:00:31 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:31 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:31 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa25fa000
Jan 1 00:00:31 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa2a62580
Jan 1 00:00:31 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:31 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 82541d04
Jan 1 00:00:32 kern info kernel: nf_conntrack version 0.5.0 (923 buckets, 3692 max)
Jan 1 00:00:33 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:34 kern info kernel: monitor task is initialized pid= 435
Jan 1 00:00:35 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:36 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:01:02 kern crit kernel: Line 0: VDSL G.993 channel analysis
Jan 1 00:01:03 kern crit kernel: Line 0: VDSL2 link up, Bearer 0, us=19999, ds=74000
Jan 1 00:01:03 kern crit kernel: Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:03 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:03 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e df 0b
Jan 1 00:01:03 kern warn kernel: [DoCreateDeviceReq.710]: register_netdev
Jan 1 00:01:03 kern warn kernel: [DoCreateDeviceReq.712]: register_netdev done
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:03 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa0d06000
Jan 1 00:01:03 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=19999000, DS=74000000
Jan 1 00:01:03 kern info kernel: NComm Ethernet 802.3AH OA&M loaded.
Jan 1 00:01:03 kern info kernel: NComm Ethernet 802.1AG OA&M loaded.
Jan 1 00:01:04 kern warn kernel: netdev path : ptm0.1
Jan 1 00:01:04 kern info kernel: ->
Jan 1 00:01:04 kern info kernel: ptm0
Jan 1 00:01:04 kern warn kernel: BCMVLAN : ptm0 mode was set to RG
Jan 1 00:01:04 kern info kernel: device ptm0.1 entered promiscuous mode
Jan 1 00:01:04 kern info kernel: device ptm0 entered promiscuous mode
Jan 1 00:01:04 kern info kernel: br0: port 6(ptm0.1) entered forwarding state
Jan 1 00:01:04 kern info kernel: br0: port 6(ptm0.1) entered forwarding state
Jan 1 00:01:16 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link UP 100 mbps full duplex
Jan 1 00:01:16 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Jan 1 00:01:16 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:16 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:17 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:17 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:01:17 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:17 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:19 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link DOWN.
Jan 1 00:01:19 kern info kernel: br0: port 4(eth3) entered disabled state
Jan 1 00:01:21 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link DOWN.
Jan 1 00:01:21 kern info kernel: br0: port 5(eth4) entered disabled state
Jan 1 00:01:23 kern crit kernel: eth3 (Int switch port: 3) (Logical Port: 3) Link UP 100 mbps full duplex
Jan 1 00:01:23 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:23 kern info kernel: br0: port 4(eth3) entered forwarding state
Jan 1 00:01:25 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:25 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:25 kern info kernel: br0: port 5(eth4) entered forwarding state

Nothing to worry about, just normal Broadcom logs (the chipset vendor of the router),

Oh thank you again Billion my 8800nl r2 was connected for 30 days oonce and DLM wasn't budging if i have to say comparing the Huawei HG612 to the 8800nl r2 the HG612 is winning by a tad bit keeping my ping lower than the 8800nl r2 is since the last time we spoke. But i dod notice the 8800nl r2 Line Attenuation is shorter by 11.3 as with the HG612 getting 12.2 so there must be some tweaks you guys can do with the firmware to get it better?