Problem with printer server

[akinsey]

I use my 7800DXL as a server for a HP2605 USB laser printer, this works perfectly if I power up the printer before powering the router. However, if I power up the printer when the router is already running it causes the router to 'hang' ie one of the PCs on my network reports an IP address conflict and the network becomes unusable. Re-booting the router resolves the problem. I don't use the printer all that often, so I prefer to power it down most of the time, being able to power it up without re-booting the router would be much appreciated

I am running with firmware version 2.31 RC4.3, although I experienced the same problem with the previous f/w.

Hoping you're able to help

[Tomken]

It's usually best to assign a printer with a static IP address outside of the DHCP range so it won't matter then when it's switched on.

If it doesn't have its MAC address on the printer, it will show up in the System Log when it has been used.

[akinsey]

My printer has a USB interface and I'm using the 7800DXL "On-board Print Server", so the router is acting as the printer server. I'm not certain with this config whether it's possible to assign a static IP address.

[billion_fan]

My printer has a USB interface and I'm using the 7800DXL "On-board Print Server", so the router is acting as the printer server. I'm not certain with this config whether it's possible to assign a static IP address.

Can you post a copy of your system log??

[akinsey]

I've attached the system log, the sequence of events is:
a) Router power-up (printer powered down)
b) Printer powered up at 10:27:27
c) The network goes down soon after this
d) Printer powered off at 10:29:24 - I did this so that I could access the log

Let me know if there's anything else you'd like me to try, thanks.

I've not been able to add the log file as an attachment, so here it is:

Jan 1 00:00:16 daemon warn kernel: BcmAdsl_Initialize=0xC01F6BD0, g_pFnNotifyCallback=0xC022B4A4
Jan 1 00:00:16 daemon warn kernel: pSdramPHY=0xAFFFFFF8, 0xFF7FBFDF 0xFFFFFFFF
Jan 1 00:00:16 daemon warn kernel: *** XfaceOffset: 0x21F90 => 0x21F90 ***
Jan 1 00:00:16 daemon warn kernel: *** PhySdramSize got adjusted: 0x8D394 => 0xA2E88 ***
Jan 1 00:00:16 daemon warn kernel: AdslCoreSharedMemInit: shareMemSize=381261(381264)
Jan 1 00:00:16 daemon warn kernel: AdslCoreHwReset: pLocSbSta=8a470000 bkupThreshold=1600
Jan 1 00:00:16 daemon warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xAFF82044
Jan 1 00:00:16 daemon warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:16 daemon warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:16 daemon warn kernel: fapDrv_psmAlloc: fapIdx=0, size: 1600, offset=b1012be0 bytes remaining 584
Jan 1 00:00:16 daemon warn kernel: XTM Init: 200 rx BDs at 0xb1012be0
Jan 1 00:00:16 daemon warn kernel: fapDrv_psmAlloc: fapIdx=0, size: 128, offset=b1013220 bytes remaining 456
Jan 1 00:00:16 daemon warn kernel: XTM Init: 16 rx BDs at 0xb1013220
Jan 1 00:00:17 daemon warn kernel: nf_conntrack version 0.5.0 (4080 buckets, 32640 max)
Jan 1 00:00:18 daemon info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:18 daemon crit kernel: Line 0: xDSL G.994 training
Jan 1 00:00:18 daemon info kernel: message received before monitor task is initialized kerSysSendtoMonitorTask
Jan 1 00:00:18 daemon info kernel: monitor task is initialized pid= 328
Jan 1 00:00:20 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:20 daemon info kernel: device wl0 left promiscuous mode
Jan 1 00:00:20 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:20 daemon info kernel: device wl0 entered promiscuous mode
Jan 1 00:00:20 daemon info kernel: br0: bridge group port 5(wl0) entering forwarding state
Jan 1 00:00:21 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:21 daemon info kernel: device wl0 left promiscuous mode
Jan 1 00:00:21 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:22 daemon info kernel: device wl0 entered promiscuous mode
Jan 1 00:00:22 daemon info kernel: br0: bridge group port 5(wl0) entering forwarding state
Jan 1 00:00:23 daemon crit kernel: eth2 (switch port: 2) Link UP 100 mbps full duplex
Jan 1 00:00:23 daemon info kernel: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
Jan 1 00:00:23 daemon info kernel: br0: bridge group port 3(eth2) entering forwarding state
Jan 1 00:00:24 daemon crit kernel: eth3 (switch port: 1) Link UP 10 mbps full duplex
Jan 1 00:00:24 daemon info kernel: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Jan 1 00:00:24 daemon info kernel: br0: bridge group port 4(eth3) entering forwarding state
Jan 1 00:00:27 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:27 daemon info kernel: device wl1 left promiscuous mode
Jan 1 00:00:27 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:27 daemon info kernel: device wl1 entered promiscuous mode
Jan 1 00:00:27 daemon info kernel: br0: bridge group port 6(wl1) entering forwarding state
Jan 1 00:00:28 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:29 daemon info kernel: device wl1 left promiscuous mode
Jan 1 00:00:29 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:29 daemon info kernel: device wl1 entered promiscuous mode
Jan 1 00:00:29 daemon info kernel: br0: bridge group port 6(wl1) entering forwarding state
Jan 1 00:00:30 daemon crit kernel: Line 0: ADSL G.992 started
Jan 1 00:00:34 daemon crit kernel: Line 0: ADSL G.992 channel analysis
Jan 1 00:00:40 daemon crit kernel: Line 0: ADSL G.992 message exchange
Jan 1 00:00:41 daemon crit kernel: Line 0: ADSL link down
Jan 1 00:00:45 daemon crit kernel: Line 0: xDSL G.994 training
Jan 1 00:00:46 daemon err syslog: dhcpd:sending OFFER of 192.168.1.100
Jan 1 00:00:47 daemon err syslog: dhcpd:sending ACK to 192.168.1.100
Jan 1 00:00:56 daemon crit kernel: Line 0: ADSL G.992 started
Jan 1 00:01:00 daemon crit kernel: Line 0: ADSL G.992 channel analysis
Jan 1 00:01:02 daemon err syslog: dhcpd:sending OFFER of 192.168.1.101
Jan 1 00:01:02 daemon err syslog: dhcpd:sending ACK to 192.168.1.101
Jan 1 00:01:07 daemon crit kernel: Line 0: ADSL G.992 message exchange
Jan 1 00:01:07 daemon crit kernel: Line 0: ADSL link up, Bearer 0, us=1016, ds=12836
Jan 1 00:01:07 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
Jan 1 00:01:07 daemon warn kernel: bcmxtmrt: MAC address: 00 04 ed ef 42 d4
Jan 1 00:01:07 daemon warn kernel: [DoCreateDeviceReq.3244]: register_netdev
Jan 1 00:01:07 daemon warn kernel: [DoCreateDeviceReq.3246]: register_netdev done
Jan 1 00:01:07 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 2
Jan 1 00:01:07 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
Jan 1 00:01:07 daemon warn kernel: XTM Init: 400 tx BDs at 0xaa644000
Jan 1 00:01:07 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1016000, DS=12836000
Jan 1 00:01:07 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
Jan 1 00:01:07 daemon warn kernel: atm0.1 MAC address set to 00:04:ED:EF:42:D5
Jan 1 00:01:07 daemon warn kernel: netdev path : atm0.1 -> atm0
Jan 1 00:01:07 daemon warn kernel: BCMVLAN : atm0 mode was set to RG
Jan 1 00:01:07 daemon info kernel: device atm0 entered promiscuous mode
Jan 1 00:01:08 daemon notice syslog: pppd:cms logging initialized.
Jan 1 00:01:08 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jan 1 00:01:08 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:10 daemon crit syslog: PPP server detected.
Jan 1 00:01:10 daemon crit syslog: PPP session established.
Jan 1 00:01:10 daemon warn kernel: netdev path : ppp0.1 -> atm0.1 -> atm0
Jan 1 00:01:10 daemon notice syslog: pppd:Using interface ppp0.1
Jan 1 00:01:10 daemon notice syslog: pppd:Connect: ppp0.1 <--> atm0.1
Jan 1 00:01:10 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jan 1 00:01:10 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:10 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:10 daemon crit syslog: PPP LCP UP.
Jan 1 00:01:10 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 6979
Jan 1 00:01:10 daemon notice syslog: pppd:local IP address 92.0.248.181
Jan 1 00:01:10 daemon notice syslog: pppd:remote IP address 92.0.240.1
Jan 1 00:01:10 daemon notice syslog: pppd:primary DNS address 62.24.243.1
Jan 1 00:01:10 daemon notice syslog: pppd:secondary DNS address 62.24.134.2
Jan 1 00:01:10 daemon crit syslog: Received valid IP address from server. Connection UP.
May 13 10:27:27 daemon info kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2
May 13 10:27:27 daemon info kernel: usb 1-1: configuration #1 chosen from 1 choice
May 13 10:27:27 daemon info kernel: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3617
May 13 10:27:27 daemon info kernel: usbcore: registered new interface driver usbserial
May 13 10:27:27 daemon info kernel: usbserial: USB Serial Driver core
May 13 10:27:27 daemon info kernel: USB Serial support registered for GSM modem (1-port)
May 13 10:27:27 daemon info kernel: option 1-1:1.1: GSM modem (1-port) converter detected
May 13 10:27:27 daemon info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
May 13 10:27:27 daemon info kernel: usbcore: registered new interface driver option
May 13 10:27:27 daemon info kernel: option: v0.7.2:USB Driver for GSM modems
May 13 10:27:32 user info syslog: check available MODEM port ..
May 13 10:28:38 daemon crit kernel: Line 0: ADSL link down
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = ATM
May 13 10:28:38 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
May 13 10:28:38 daemon warn kernel: HOST XTM tx ch 0 disabled.
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
May 13 10:28:38 daemon crit kernel: Line 0: ADSL link up, Bearer 0, us=1016, ds=12836
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
May 13 10:28:38 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
May 13 10:28:38 daemon warn kernel: XTM Init: 400 tx BDs at 0xaa644000
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1016000, DS=12836000
May 13 10:28:39 daemon crit kernel: Line 0: ADSL link down
May 13 10:28:39 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = ATM
May 13 10:28:39 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
May 13 10:28:39 daemon warn kernel: HOST XTM tx ch 0 disabled.
May 13 10:28:39 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
May 13 10:29:24 daemon warn kernel: pSdramPHY=0xAFFFFFF8, 0x39D08 0xDEADBEEF
May 13 10:29:24 daemon warn kernel: *** XfaceOffset: 0x21F90 => 0x21F90 ***
May 13 10:29:24 daemon warn kernel: *** PhySdramSize got adjusted: 0x8D394 => 0xA2E88 ***
May 13 10:29:24 daemon warn kernel: AdslCoreSharedMemInit: shareMemSize=381261(381264)
May 13 10:29:24 daemon warn kernel: AdslCoreHwReset: pLocSbSta=8a470000 bkupThreshold=1600
May 13 10:29:24 daemon warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xAFF82044
May 13 10:29:24 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
May 13 10:29:24 daemon info kernel: usb 1-1: USB disconnect, address 2
May 13 10:29:24 daemon info kernel: usblp0: removed
May 13 10:29:24 daemon info kernel: option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
May 13 10:29:24 daemon info kernel: option 1-1:1.1: device disconnected
May 13 10:29:25 user info syslog: available MODEM port : ..
May 13 10:29:25 user err syslog: Error: The 3gfunc dev is NULL and exit the 3gfunc
May 13 10:29:25 daemon info kernel: usbcore: deregistering interface driver option
May 13 10:29:25 daemon info kernel: USB Serial deregistering driver GSM modem (1-port)
May 13 10:29:25 daemon info kernel: usbcore: deregistering interface driver usbserial
May 13 10:29:27 daemon notice syslog: pppd:Terminating on signal 20.
May 13 10:29:27 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
May 13 10:29:27 daemon crit syslog: Clear IP addresses. Connection DOWN.
May 13 10:29:27 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
May 13 10:29:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
May 13 10:29:29 daemon crit kernel: Line 0: xDSL G.994 training
May 13 10:29:32 daemon info kernel: device atm0 left promiscuous mode
May 13 10:29:32 daemon info kernel: device atm0 entered promiscuous mode
May 13 10:29:32 daemon info kernel: device atm0 left promiscuous mode
May 13 10:29:40 daemon crit kernel: Line 0: ADSL G.992 started
May 13 10:29:45 daemon crit kernel: Line 0: ADSL G.992 channel analysis
May 13 10:29:51 daemon crit kernel: Line 0: ADSL G.992 message exchange
May 13 10:29:52 daemon crit kernel: Line 0: ADSL link down
May 13 10:29:55 daemon crit kernel: Line 0: xDSL G.994 training
May 13 10:30:06 daemon crit kernel: Line 0: ADSL G.992 started
May 13 10:30:11 daemon crit kernel: Line 0: ADSL G.992 channel analysis
May 13 10:30:17 daemon crit kernel: Line 0: ADSL G.992 message exchange
May 13 10:30:17 daemon crit kernel: Line 0: ADSL link up, Bearer 0, us=961, ds=12812
May 13 10:30:17 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
May 13 10:30:17 daemon warn kernel: bcmxtmrt: MAC address: 00 04 ed ef 42 d4
May 13 10:30:17 daemon warn kernel: [DoCreateDeviceReq.3244]: register_netdev
May 13 10:30:18 daemon warn kernel: [DoCreateDeviceReq.3246]: register_netdev done
May 13 10:30:18 daemon warn kernel: bcmxtmrt: DSD(8fae9cfc) - 128
May 13 10:30:18 daemon warn kernel: XTM Init: 400 tx BDs at 0xaa720000
May 13 10:30:18 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=961000, DS=12812000
May 13 10:30:18 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 2
May 13 10:30:18 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
May 13 10:30:18 daemon warn kernel: atm0.1 MAC address set to 00:04:ED:EF:42:D5
May 13 10:30:18 daemon warn kernel: netdev path : atm0.1 -> atm0
May 13 10:30:18 daemon warn kernel: BCMVLAN : atm0 mode was set to RG
May 13 10:30:18 daemon info kernel: device atm0 entered promiscuous mode
May 13 10:30:18 daemon notice syslog: pppd:cms logging initialized.
May 13 10:30:18 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
May 13 10:30:18 daemon notice syslog: PPP: Start to connect ...
May 13 10:30:23 daemon crit syslog: PPP server detected.
May 13 10:30:23 daemon crit syslog: PPP session established.
May 13 10:30:23 daemon warn kernel: netdev path : ppp0.1
May 13 10:30:23 daemon info kernel: ->
May 13 10:30:23 daemon info kernel: atm0.1 ->
May 13 10:30:23 daemon info kernel: atm0
May 13 10:30:23 daemon notice syslog: pppd:Using interface ppp0.1
May 13 10:30:23 daemon notice syslog: pppd:Connect: ppp0.1 <--> atm0.1
May 13 10:30:23 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
May 13 10:30:23 daemon err syslog: pppd:Couldn't increase MRU to 1500
May 13 10:30:23 daemon err syslog: pppd:Couldn't increase MRU to 1500
May 13 10:30:23 daemon crit syslog: PPP LCP UP.
May 13 10:30:23 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 7470
May 13 10:30:23 daemon notice syslog: pppd:local IP address 92.0.248.210
May 13 10:30:23 daemon notice syslog: pppd:remote IP address 92.0.240.1
May 13 10:30:23 daemon notice syslog: pppd:primary DNS address 62.24.243.1
May 13 10:30:23 daemon notice syslog: pppd:secondary DNS address 62.24.134.2
May 13 10:30:23 daemon crit syslog: Received valid IP address from server. Connection UP.

[billion_fan]

I've attached the system log, the sequence of events is:
a) Router power-up (printer powered down)
b) Printer powered up at 10:27:27
c) The network goes down soon after this
d) Printer powered off at 10:29:24 - I did this so that I could access the log

Let me know if there's anything else you'd like me to try, thanks.

I've not been able to add the log file as an attachment, so here it is:

Jan 1 00:00:16 daemon warn kernel: BcmAdsl_Initialize=0xC01F6BD0, g_pFnNotifyCallback=0xC022B4A4
Jan 1 00:00:16 daemon warn kernel: pSdramPHY=0xAFFFFFF8, 0xFF7FBFDF 0xFFFFFFFF
Jan 1 00:00:16 daemon warn kernel: *** XfaceOffset: 0x21F90 => 0x21F90 ***
Jan 1 00:00:16 daemon warn kernel: *** PhySdramSize got adjusted: 0x8D394 => 0xA2E88 ***
Jan 1 00:00:16 daemon warn kernel: AdslCoreSharedMemInit: shareMemSize=381261(381264)
Jan 1 00:00:16 daemon warn kernel: AdslCoreHwReset: pLocSbSta=8a470000 bkupThreshold=1600
Jan 1 00:00:16 daemon warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xAFF82044
Jan 1 00:00:16 daemon warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:16 daemon warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:16 daemon warn kernel: fapDrv_psmAlloc: fapIdx=0, size: 1600, offset=b1012be0 bytes remaining 584
Jan 1 00:00:16 daemon warn kernel: XTM Init: 200 rx BDs at 0xb1012be0
Jan 1 00:00:16 daemon warn kernel: fapDrv_psmAlloc: fapIdx=0, size: 128, offset=b1013220 bytes remaining 456
Jan 1 00:00:16 daemon warn kernel: XTM Init: 16 rx BDs at 0xb1013220
Jan 1 00:00:17 daemon warn kernel: nf_conntrack version 0.5.0 (4080 buckets, 32640 max)
Jan 1 00:00:18 daemon info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:18 daemon crit kernel: Line 0: xDSL G.994 training
Jan 1 00:00:18 daemon info kernel: message received before monitor task is initialized kerSysSendtoMonitorTask
Jan 1 00:00:18 daemon info kernel: monitor task is initialized pid= 328
Jan 1 00:00:20 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:20 daemon info kernel: device wl0 left promiscuous mode
Jan 1 00:00:20 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:20 daemon info kernel: device wl0 entered promiscuous mode
Jan 1 00:00:20 daemon info kernel: br0: bridge group port 5(wl0) entering forwarding state
Jan 1 00:00:21 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:21 daemon info kernel: device wl0 left promiscuous mode
Jan 1 00:00:21 daemon info kernel: br0: bridge group port 5(wl0) entering disabled state
Jan 1 00:00:22 daemon info kernel: device wl0 entered promiscuous mode
Jan 1 00:00:22 daemon info kernel: br0: bridge group port 5(wl0) entering forwarding state
Jan 1 00:00:23 daemon crit kernel: eth2 (switch port: 2) Link UP 100 mbps full duplex
Jan 1 00:00:23 daemon info kernel: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
Jan 1 00:00:23 daemon info kernel: br0: bridge group port 3(eth2) entering forwarding state
Jan 1 00:00:24 daemon crit kernel: eth3 (switch port: 1) Link UP 10 mbps full duplex
Jan 1 00:00:24 daemon info kernel: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Jan 1 00:00:24 daemon info kernel: br0: bridge group port 4(eth3) entering forwarding state
Jan 1 00:00:27 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:27 daemon info kernel: device wl1 left promiscuous mode
Jan 1 00:00:27 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:27 daemon info kernel: device wl1 entered promiscuous mode
Jan 1 00:00:27 daemon info kernel: br0: bridge group port 6(wl1) entering forwarding state
Jan 1 00:00:28 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:29 daemon info kernel: device wl1 left promiscuous mode
Jan 1 00:00:29 daemon info kernel: br0: bridge group port 6(wl1) entering disabled state
Jan 1 00:00:29 daemon info kernel: device wl1 entered promiscuous mode
Jan 1 00:00:29 daemon info kernel: br0: bridge group port 6(wl1) entering forwarding state
Jan 1 00:00:30 daemon crit kernel: Line 0: ADSL G.992 started
Jan 1 00:00:34 daemon crit kernel: Line 0: ADSL G.992 channel analysis
Jan 1 00:00:40 daemon crit kernel: Line 0: ADSL G.992 message exchange
Jan 1 00:00:41 daemon crit kernel: Line 0: ADSL link down
Jan 1 00:00:45 daemon crit kernel: Line 0: xDSL G.994 training
Jan 1 00:00:46 daemon err syslog: dhcpd:sending OFFER of 192.168.1.100
Jan 1 00:00:47 daemon err syslog: dhcpd:sending ACK to 192.168.1.100
Jan 1 00:00:56 daemon crit kernel: Line 0: ADSL G.992 started
Jan 1 00:01:00 daemon crit kernel: Line 0: ADSL G.992 channel analysis
Jan 1 00:01:02 daemon err syslog: dhcpd:sending OFFER of 192.168.1.101
Jan 1 00:01:02 daemon err syslog: dhcpd:sending ACK to 192.168.1.101
Jan 1 00:01:07 daemon crit kernel: Line 0: ADSL G.992 message exchange
Jan 1 00:01:07 daemon crit kernel: Line 0: ADSL link up, Bearer 0, us=1016, ds=12836
Jan 1 00:01:07 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
Jan 1 00:01:07 daemon warn kernel: bcmxtmrt: MAC address: 00 04 ed ef 42 d4
Jan 1 00:01:07 daemon warn kernel: [DoCreateDeviceReq.3244]: register_netdev
Jan 1 00:01:07 daemon warn kernel: [DoCreateDeviceReq.3246]: register_netdev done
Jan 1 00:01:07 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 2
Jan 1 00:01:07 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
Jan 1 00:01:07 daemon warn kernel: XTM Init: 400 tx BDs at 0xaa644000
Jan 1 00:01:07 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1016000, DS=12836000
Jan 1 00:01:07 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
Jan 1 00:01:07 daemon warn kernel: atm0.1 MAC address set to 00:04:ED:EF:42:D5
Jan 1 00:01:07 daemon warn kernel: netdev path : atm0.1 -> atm0
Jan 1 00:01:07 daemon warn kernel: BCMVLAN : atm0 mode was set to RG
Jan 1 00:01:07 daemon info kernel: device atm0 entered promiscuous mode
Jan 1 00:01:08 daemon notice syslog: pppd:cms logging initialized.
Jan 1 00:01:08 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jan 1 00:01:08 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:10 daemon crit syslog: PPP server detected.
Jan 1 00:01:10 daemon crit syslog: PPP session established.
Jan 1 00:01:10 daemon warn kernel: netdev path : ppp0.1 -> atm0.1 -> atm0
Jan 1 00:01:10 daemon notice syslog: pppd:Using interface ppp0.1
Jan 1 00:01:10 daemon notice syslog: pppd:Connect: ppp0.1 <--> atm0.1
Jan 1 00:01:10 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jan 1 00:01:10 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:10 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:10 daemon crit syslog: PPP LCP UP.
Jan 1 00:01:10 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 6979
Jan 1 00:01:10 daemon notice syslog: pppd:local IP address 92.0.248.181
Jan 1 00:01:10 daemon notice syslog: pppd:remote IP address 92.0.240.1
Jan 1 00:01:10 daemon notice syslog: pppd:primary DNS address 62.24.243.1
Jan 1 00:01:10 daemon notice syslog: pppd:secondary DNS address 62.24.134.2
Jan 1 00:01:10 daemon crit syslog: Received valid IP address from server. Connection UP.
May 13 10:27:27 daemon info kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2
May 13 10:27:27 daemon info kernel: usb 1-1: configuration #1 chosen from 1 choice
May 13 10:27:27 daemon info kernel: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3617
May 13 10:27:27 daemon info kernel: usbcore: registered new interface driver usbserial
May 13 10:27:27 daemon info kernel: usbserial: USB Serial Driver core
May 13 10:27:27 daemon info kernel: USB Serial support registered for GSM modem (1-port)
May 13 10:27:27 daemon info kernel: option 1-1:1.1: GSM modem (1-port) converter detected
May 13 10:27:27 daemon info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
May 13 10:27:27 daemon info kernel: usbcore: registered new interface driver option
May 13 10:27:27 daemon info kernel: option: v0.7.2:USB Driver for GSM modems
May 13 10:27:32 user info syslog: check available MODEM port ..
May 13 10:28:38 daemon crit kernel: Line 0: ADSL link down
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = ATM
May 13 10:28:38 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
May 13 10:28:38 daemon warn kernel: HOST XTM tx ch 0 disabled.
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
May 13 10:28:38 daemon crit kernel: Line 0: ADSL link up, Bearer 0, us=1016, ds=12836
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
May 13 10:28:38 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
May 13 10:28:38 daemon warn kernel: XTM Init: 400 tx BDs at 0xaa644000
May 13 10:28:38 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1016000, DS=12836000
May 13 10:28:39 daemon crit kernel: Line 0: ADSL link down
May 13 10:28:39 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN, Service Support = ATM
May 13 10:28:39 daemon warn kernel: bcmxtmrt: DSD(8a5bb49c) - 128
May 13 10:28:39 daemon warn kernel: HOST XTM tx ch 0 disabled.
May 13 10:28:39 daemon warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
May 13 10:29:24 daemon warn kernel: pSdramPHY=0xAFFFFFF8, 0x39D08 0xDEADBEEF
May 13 10:29:24 daemon warn kernel: *** XfaceOffset: 0x21F90 => 0x21F90 ***
May 13 10:29:24 daemon warn kernel: *** PhySdramSize got adjusted: 0x8D394 => 0xA2E88 ***
May 13 10:29:24 daemon warn kernel: AdslCoreSharedMemInit: shareMemSize=381261(381264)
May 13 10:29:24 daemon warn kernel: AdslCoreHwReset: pLocSbSta=8a470000 bkupThreshold=1600
May 13 10:29:24 daemon warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xAFF82044
May 13 10:29:24 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
May 13 10:29:24 daemon info kernel: usb 1-1: USB disconnect, address 2
May 13 10:29:24 daemon info kernel: usblp0: removed
May 13 10:29:24 daemon info kernel: option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
May 13 10:29:24 daemon info kernel: option 1-1:1.1: device disconnected
May 13 10:29:25 user info syslog: available MODEM port : ..
May 13 10:29:25 user err syslog: Error: The 3gfunc dev is NULL and exit the 3gfunc
May 13 10:29:25 daemon info kernel: usbcore: deregistering interface driver option
May 13 10:29:25 daemon info kernel: USB Serial deregistering driver GSM modem (1-port)
May 13 10:29:25 daemon info kernel: usbcore: deregistering interface driver usbserial
May 13 10:29:27 daemon notice syslog: pppd:Terminating on signal 20.
May 13 10:29:27 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
May 13 10:29:27 daemon crit syslog: Clear IP addresses. Connection DOWN.
May 13 10:29:27 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
May 13 10:29:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
May 13 10:29:29 daemon crit kernel: Line 0: xDSL G.994 training
May 13 10:29:32 daemon info kernel: device atm0 left promiscuous mode
May 13 10:29:32 daemon info kernel: device atm0 entered promiscuous mode
May 13 10:29:32 daemon info kernel: device atm0 left promiscuous mode
May 13 10:29:40 daemon crit kernel: Line 0: ADSL G.992 started
May 13 10:29:45 daemon crit kernel: Line 0: ADSL G.992 channel analysis
May 13 10:29:51 daemon crit kernel: Line 0: ADSL G.992 message exchange
May 13 10:29:52 daemon crit kernel: Line 0: ADSL link down
May 13 10:29:55 daemon crit kernel: Line 0: xDSL G.994 training
May 13 10:30:06 daemon crit kernel: Line 0: ADSL G.992 started
May 13 10:30:11 daemon crit kernel: Line 0: ADSL G.992 channel analysis
May 13 10:30:17 daemon crit kernel: Line 0: ADSL G.992 message exchange
May 13 10:30:17 daemon crit kernel: Line 0: ADSL link up, Bearer 0, us=961, ds=12812
May 13 10:30:17 daemon warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
May 13 10:30:17 daemon warn kernel: bcmxtmrt: MAC address: 00 04 ed ef 42 d4
May 13 10:30:17 daemon warn kernel: [DoCreateDeviceReq.3244]: register_netdev
May 13 10:30:18 daemon warn kernel: [DoCreateDeviceReq.3246]: register_netdev done
May 13 10:30:18 daemon warn kernel: bcmxtmrt: DSD(8fae9cfc) - 128
May 13 10:30:18 daemon warn kernel: XTM Init: 400 tx BDs at 0xaa720000
May 13 10:30:18 daemon warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=961000, DS=12812000
May 13 10:30:18 daemon warn kernel: [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 2
May 13 10:30:18 daemon warn kernel: [FAP0] xtmLinkUp : devId 0, matchId 0
May 13 10:30:18 daemon warn kernel: atm0.1 MAC address set to 00:04:ED:EF:42:D5
May 13 10:30:18 daemon warn kernel: netdev path : atm0.1 -> atm0
May 13 10:30:18 daemon warn kernel: BCMVLAN : atm0 mode was set to RG
May 13 10:30:18 daemon info kernel: device atm0 entered promiscuous mode
May 13 10:30:18 daemon notice syslog: pppd:cms logging initialized.
May 13 10:30:18 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
May 13 10:30:18 daemon notice syslog: PPP: Start to connect ...
May 13 10:30:23 daemon crit syslog: PPP server detected.
May 13 10:30:23 daemon crit syslog: PPP session established.
May 13 10:30:23 daemon warn kernel: netdev path : ppp0.1
May 13 10:30:23 daemon info kernel: ->
May 13 10:30:23 daemon info kernel: atm0.1 ->
May 13 10:30:23 daemon info kernel: atm0
May 13 10:30:23 daemon notice syslog: pppd:Using interface ppp0.1
May 13 10:30:23 daemon notice syslog: pppd:Connect: ppp0.1 <--> atm0.1
May 13 10:30:23 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
May 13 10:30:23 daemon err syslog: pppd:Couldn't increase MRU to 1500
May 13 10:30:23 daemon err syslog: pppd:Couldn't increase MRU to 1500
May 13 10:30:23 daemon crit syslog: PPP LCP UP.
May 13 10:30:23 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 7470
May 13 10:30:23 daemon notice syslog: pppd:local IP address 92.0.248.210
May 13 10:30:23 daemon notice syslog: pppd:remote IP address 92.0.240.1
May 13 10:30:23 daemon notice syslog: pppd:primary DNS address 62.24.243.1
May 13 10:30:23 daemon notice syslog: pppd:secondary DNS address 62.24.134.2
May 13 10:30:23 daemon crit syslog: Received valid IP address from server. Connection UP.

So just to confirm when the issue occurs, all devices that connected to the router cannot use the internet or login to the router?? If you have another PC to verify this would be great.

Once the printer is turned off everything jumps back to life?

[akinsey]

That's correct, all devices connected to the router cannot access either the internet or router.

Very soon after the printer is turned off the network functionality comes back.

[billion_fan]

That's correct, all devices connected to the router cannot access either the internet or router.

Very soon after the printer is turned off the network functionality comes back.

I have forwarded your logs over to our engineers, once they reply I will drop you a update.

[billion_fan]

That's correct, all devices connected to the router cannot access either the internet or router.

Very soon after the printer is turned off the network functionality comes back.

Can you sumbit a ticket here, our engineers are requesting a backup of you config file, I would like your case to be officially logged.

http://www.billion.uk.com/esupport/inde ... ets/Submit

[billion_fan]

Just sent you a ticket reply, let us know how you get on